EBK MANUFACTURING ENGINEERING & TECHNOL
7th Edition
ISBN: 8220100793431
Author: KALPAKJIAN
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 32, Problem 21QLP
Explain why adhesively bonded joints tend to be weak in peeling.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Identify the conditions under which a brazed joint is likely to be “stronger” than the brazing material by itself. Describe the trends in joint fracture strength as it becomes wider/narrower or thinner/thicker.
What do you understand by the term riveted joint? Explain the necessity of such a joint.
Write down the damage patterns that occur in the rivet joints that are forced axially. Explain how strength calculations are made under static stresses.
Chapter 32 Solutions
EBK MANUFACTURING ENGINEERING & TECHNOL
Ch. 32 - What is the difference between brazing and...Ch. 32 - Are fluxes necessary in brazing? If so, why?Ch. 32 - Why is surface preparation important in...Ch. 32 - What materials are typically used in solder?Ch. 32 - Soldering is generally applied to thinner...Ch. 32 - Explain the reasons why a variety of mechanical...Ch. 32 - List three brazing and three soldering techniques.Ch. 32 - Describe the similarities and differences between...Ch. 32 - What precautions should be taken in the...Ch. 32 - What difficulties are involved in joining...
Ch. 32 - Prob. 11RQCh. 32 - What are the principles of (a) wave soldering...Ch. 32 - What is a peel test? Why is it useful?Ch. 32 - What is a combination joint?Ch. 32 - Prob. 15RQCh. 32 - Prob. 16QLPCh. 32 - Prob. 17QLPCh. 32 - Comment on your observations concerning the...Ch. 32 - Give examples of combination joints other than...Ch. 32 - Discuss the need for fixtures for holding...Ch. 32 - Explain why adhesively bonded joints tend to be...Ch. 32 - It is common practice to tin-plate electrical...Ch. 32 - Give three applications where adhesive-bonding is...Ch. 32 - Prob. 24QLPCh. 32 - If you are designing a joint that must be strong...Ch. 32 - Prob. 26QLPCh. 32 - Rate lap, butt, and scarf joints in terms of...Ch. 32 - Prob. 28QLPCh. 32 - Prob. 29QTPCh. 32 - Prob. 30QTPCh. 32 - Prob. 31QTPCh. 32 - Figure 32.4 shows qualitatively the tensile and...Ch. 32 - When manufacturing the fuselage of a commuter...Ch. 32 - Prob. 34SDPCh. 32 - Name several products that have been assembled...Ch. 32 - Suggest methods of attaching a round bar (made of...Ch. 32 - Prob. 38SDPCh. 32 - Prob. 39SDPCh. 32 - Prob. 40SDPCh. 32 - Prob. 41SDPCh. 32 - Describe part shapes that cannot be joined by...Ch. 32 - Prob. 43SDPCh. 32 - Prob. 44SDPCh. 32 - Prob. 45SDPCh. 32 - Prob. 46SDPCh. 32 - Review Fig. 32.9a and explain the shortcoming...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Explain with neat sketch, the joining process of “Riveting”.arrow_forward2) Explain how a cylindrical joint can be practically realised?arrow_forward(a) State 5 factors affecting chip formation during metal cutting (b) outline the principle of Ultrasonic testing for checking deeply imbedded defects in a welded jointarrow_forward
- Please explain the significance of residual stress in welded structures and the ways to deal with this problem.arrow_forward(b) You are required to joint two parts together by joining process. One of the parts needs to be remove out of an assembly and replaced with a new part several times during the product's life due to failure. Recommend a suitable ioining process for this condition with ONE (1) example.arrow_forwardWhy is cost a consideration in joint design?arrow_forward
- Two 1.2 mm thick flat copper sheets are being spot welded using a current of 6000A and a current flow time of 0.18 s. The electrodes are 5 mm in diameter. Estimate the generated in the weld zone. Take effective resistance as 150 ohm. also calculate temperature rise assuming that the heat generated is confined to the volume ogf materials directly between two electrodes and temperature is uniformly distributed.arrow_forwardUnderstand cohesive and adhesive forces.arrow_forwardExplain or contradict the choice to use the following materials as hot-melt adhesives for anapplication in which the assembled part is subjected to impact-type loading. 1. Polyethylene 2. Polystyrene3. Polybutadiene4. Styrene-butadiene thermoplastic elastomer.5. Polyacrylonitrilearrow_forward
- Determine the effects of two-dimensional and three-dimensional loading on the dimensions of a given material with regard to a simple joining block.arrow_forwardIn which industries riveted joints find its application, provide list of engineering components of the specific industry?arrow_forwardA pipe can be manufactured as (a) seamless (cold rolled and extruded) or (b) hot rolled and welded. (i) Describe the process for manufacturing each type of pipe: (a) Seamless (cold rolled and extruded) pipe; (b) Hot rolled and welded pipe. (ii) Why might a cold rolled seamless pipe be better suited to drilling operations than a hot rolled and welded pipe? A particle reinforced composite (containing flakes) has particles evenly distributed throughout the matrix where the rule of mixtures applies. (i) State THREE effects that a larger volume of carbon particles within the matrix produces. A drill bit is a cutting tool on the end of a rotary subsea drill. A Thermally Stable Polycrystalline (TSP) drill bit can be used to drill a subsea well. TSP bits are man-made polycrystalline structures consisting of a multitude of synthetic diamond crystals sintered together at high pressure and temperature, used to aid cutting into hard rock formations. (i) Describe THREE reasons why this type…arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
EVERYTHING on Axial Loading Normal Stress in 10 MINUTES - Mechanics of Materials; Author: Less Boring Lectures;https://www.youtube.com/watch?v=jQ-fNqZWrNg;License: Standard YouTube License, CC-BY