EBK MANUFACTURING ENGINEERING & TECHNOL
7th Edition
ISBN: 8220100793431
Author: KALPAKJIAN
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 32, Problem 24QLP
To determine
How important is a close fit for two parts that are tobe brazed? Explain.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Give detail classification of all weldin processes and their practical applications.
Give some examples of Fastener Spacing?
Enumerate the different types of riveted joints and rivets.
Chapter 32 Solutions
EBK MANUFACTURING ENGINEERING & TECHNOL
Ch. 32 - What is the difference between brazing and...Ch. 32 - Are fluxes necessary in brazing? If so, why?Ch. 32 - Why is surface preparation important in...Ch. 32 - What materials are typically used in solder?Ch. 32 - Soldering is generally applied to thinner...Ch. 32 - Explain the reasons why a variety of mechanical...Ch. 32 - List three brazing and three soldering techniques.Ch. 32 - Describe the similarities and differences between...Ch. 32 - What precautions should be taken in the...Ch. 32 - What difficulties are involved in joining...
Ch. 32 - Prob. 11RQCh. 32 - What are the principles of (a) wave soldering...Ch. 32 - What is a peel test? Why is it useful?Ch. 32 - What is a combination joint?Ch. 32 - Prob. 15RQCh. 32 - Prob. 16QLPCh. 32 - Prob. 17QLPCh. 32 - Comment on your observations concerning the...Ch. 32 - Give examples of combination joints other than...Ch. 32 - Discuss the need for fixtures for holding...Ch. 32 - Explain why adhesively bonded joints tend to be...Ch. 32 - It is common practice to tin-plate electrical...Ch. 32 - Give three applications where adhesive-bonding is...Ch. 32 - Prob. 24QLPCh. 32 - If you are designing a joint that must be strong...Ch. 32 - Prob. 26QLPCh. 32 - Rate lap, butt, and scarf joints in terms of...Ch. 32 - Prob. 28QLPCh. 32 - Prob. 29QTPCh. 32 - Prob. 30QTPCh. 32 - Prob. 31QTPCh. 32 - Figure 32.4 shows qualitatively the tensile and...Ch. 32 - When manufacturing the fuselage of a commuter...Ch. 32 - Prob. 34SDPCh. 32 - Name several products that have been assembled...Ch. 32 - Suggest methods of attaching a round bar (made of...Ch. 32 - Prob. 38SDPCh. 32 - Prob. 39SDPCh. 32 - Prob. 40SDPCh. 32 - Prob. 41SDPCh. 32 - Describe part shapes that cannot be joined by...Ch. 32 - Prob. 43SDPCh. 32 - Prob. 44SDPCh. 32 - Prob. 45SDPCh. 32 - Prob. 46SDPCh. 32 - Review Fig. 32.9a and explain the shortcoming...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Do all braze joints resist corrosion? Give an example.arrow_forwardQuestion 01: Draw and label any screw thread and a fastener separately. Also, discuss the types of stresses acting on screw threads and fasteners.arrow_forwardWhat is welding and what type of fastening is it? Draw any four elementary weld symbols with its designation and illustration.arrow_forward
- Give information about the reasons why the weld is preferred over other fastening methods.arrow_forwardIn brazing process the joint strength is generally_ a welded joint. * None of the mentioned Larger than Smaller than Equal to Cast iron and steel pipes are produced by; * Plaster mold casting Centrifugal casting Investment casting Die castingarrow_forwardreport about Soldering.arrow_forward
- A welding operation is time-studied during which an operator was pace-rated as 120%. The operator took, on an average, 8 minutes for producing the weld-joint. If a total of 10% allowances are allowed for this operation. What is the expected standard production rate of the weld-joint in units per 8 hour day?arrow_forwardSketch 2 NDT symbols illustrating different methods that can be used to indicate multiple test requirments for the same section of weld.arrow_forwardWhat is the difference between soldering, brazing and welding?arrow_forward
- Name three methods used to perform welding, cutting,or brazing operations.arrow_forwardHard soldering of metals can be done in the melting point temperature range of O 183°C-212°C 650°C-700°C O 1600°C-1700°C O 6000°C-7000°Carrow_forwardWhat is a cold solder joint? Identify its causes, its appearance, and the means of correction.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Materials Science Mechanical Engineering - Part 3 Corrosion Explained; Author: Mega Mechatronics;https://www.youtube.com/watch?v=Il-abRhrzFY;License: Standard Youtube License