(a)
Interpretation:
The major advantages and principle limitations of thermal conductivity detector is to be stated.
Concept introduction:
Thermal conductivity can be defined as the ability of a material to conduct heat.
(b)
Interpretation:
The major advantages and principle limitations of atomic emission detector is to be stated.
Concept introduction:
Atomic emission occurs when an atom emits some specific wavelengths.
(c)
Interpretation:
The major advantages and principle limitations of thermionic detector is to be stated.
Concept introduction:
Thermionic emissions occur when electrons are excited from a heated source.
(d)
Interpretation:
The major advantages and principle limitations of the electron captive detector is to be stated.
Concept introduction:
The electron captive is the process of making unstable atoms more stable.
(e)
Interpretation:
The major advantages and principle limitations of flame photometric detector is to be stated.
Concept introduction:
Flame photometry is utilized for inorganic chemical analysis. It can detect the concentration of some metals like lithium, sodium, calcium and more.
(f)
Interpretation:
The major advantages and principle limitations of flame ionization detector is to be stated.
Concept introduction:
Flame ionization detection is a device used to measure the analyte in a gas flow.
Want to see the full answer?
Check out a sample textbook solutionChapter 27 Solutions
Principles of Instrumental Analysis
- The following calibration data were obtained by an atomic absorption spectrophotometric (AAS) method for the determination of mercury in an herbal product. (show complete solution) 1. What is the detection limit for the method? 2. What is the limit of quantitation for the method?arrow_forwardThe Na* concentration in a blood serum sample was determined using the method of standard addition and atomic spectroscopy. 25.00 mL aliquots of serum were pipetted into five 50.00 mL volumetric flasks into which 2.640 M NaCl standard was added as shown in the table below. After dilution to volume, the emission of each solution was measured and used to plot a calibration graph. Flask 1 23 4 5 Vol. of standard (mL) 0 1.00 2.00 3.00 4.00 Emission signal 3.13 5.40 7.89 10.30 12.48 Analytical signal (emission) 14 42 10 12 4 2 0 0 0.05 y = 44.697x + 3.12 R² = 0.9995 0.1 0.15 Concentration of added analyte (M) 0.2 a) Using the plotted calibration graph, calculate the Na* concentration in the blood serum sample. b) Provide a possible reason why the serum sample might have been analysed using this analytical procedure. 0.25arrow_forwardWhat is limit of detection? What is standard deviation?arrow_forward
- Replicate tests showed the following lead content results of a blood sample: 0.752, 0.756, 0.752, 0.751, and 0.760 ppm Pb. Calculate the (a) the mean (b) the standard deviation (c) the variance (d) the relative standard deviation in parts per thousand, (e) the coefficient of variation, and (f) the spread.arrow_forwardDescribe with illustrations the observed peak for a chromatogram with the following tailing factors (TF): a. TF = 1b. TF > 1c. TF < 1arrow_forwardList the desirable characteristics of HPLC detectors.arrow_forward
- Analysis of several plant-food preparations for potassium ion yielded the following data: Sample Percent K+ 1 3.90, 3.96, 4.16, 3.96 2 4.48, 4.65, 4.68, 4.42 Find the mean ; standard deviation variance and RSD for each sample.arrow_forwardThe same chloride analysis but using a new method for which the standard deviation was not known, gave the following replicate results, mean and estimated standard deviation: Chloride (ppm) = 346, 359, 350; Mean = 351.67 ppm; Standard deviation = 6.66ppm. Solve for the CI for the 3 determinations at 95% probability level.arrow_forwardcont irmation True or false: The purpose of the internal standard is to make quantitation of the analyte insensitive to injection errorsarrow_forward
- What are the requirements of a primary standard?arrow_forwardi need ans very very fast in 20 min and thank you | dont give me ans in websitearrow_forwardThe following results were obtained in the replicate determination of the lead content of a blood sample: 0.752, 0.756, 0.752, 0.751, and 0.760 ppm Pb. Calculate the relative standard deviation and coefficient of variation of this set of dataarrow_forward
- Principles of Instrumental AnalysisChemistryISBN:9781305577213Author:Douglas A. Skoog, F. James Holler, Stanley R. CrouchPublisher:Cengage LearningGeneral, Organic, and Biological ChemistryChemistryISBN:9781285853918Author:H. Stephen StokerPublisher:Cengage Learning
- Organic And Biological ChemistryChemistryISBN:9781305081079Author:STOKER, H. Stephen (howard Stephen)Publisher:Cengage Learning,