Concept explainers
Regenerative Braking Many electric cars can capture the kinetic energy of the car and store it in a capacitor or a battery by means of an electric generator. If a 1380-kg electric car brakes from 11.0 m/s to rest and charges a capacitor to 202 V, what capacitance is needed to store all of the car’s kinetic energy?
Want to see the full answer?
Check out a sample textbook solutionChapter 20 Solutions
Physics, Books a la Carte Edition (5th Edition)
Additional Science Textbook Solutions
Campbell Essential Biology with Physiology (5th Edition)
Applications and Investigations in Earth Science (9th Edition)
Chemistry: An Introduction to General, Organic, and Biological Chemistry (13th Edition)
Physics for Scientists and Engineers: A Strategic Approach, Vol. 1 (Chs 1-21) (4th Edition)
Microbiology: An Introduction
Laboratory Experiments in Microbiology (12th Edition) (What's New in Microbiology)
- Unreasonable Results (a) On a particular day, it takes 9.60 103 J of electric energy to start a truck’s engine. Calculate the capacitance of a capacitor that could store that amount of energy at 12.0 V. (b) What is unreasonable about this result? (c) Which assumptions are responsible?arrow_forwardCalculate the equivalent capacitance between points a and b in Figure P26.77. Notice that this system is not a simple series or parallel combination. Suggestion: Assume a potential difference v between [joints a and b. Write expressions for vab in terms of the charges and capacitances for the various possible pathways from a to b and require conservation of charge for those capacitor plates that are connected to each other.arrow_forwardA parallel-plate capacitor has capacitance 3.00 F. (a) How much energy is stored in the capacitor if it is connected to a 6.00-V battery? (b) If the battery is disconnected and the distance between the charged plates doubled, what is the energy stored? (c) The battery is subsequently reattached to the capacitor, but the plate separation remains as in part (b). How much energy is stored? (Answer each part in microjoules.)arrow_forward
- Earth can be considered as a spherical capacitor with two plates, where the negative plate is the surface of Earth and the positive plate is the bottom of the ionosphere, which is located at an altitude of approximately 70 km. The potential difference between Earth’s surface and the ionosphere is about 350,000 V. (a) Calculate the capacitance of this system, (b) Find the total charge on this capacitor, (c) Find the energy stored in this system.arrow_forwardA parallel-plate capacitor with only air between its plates is charged by connecting the capacitor to a battery. The capacitor is then disconnected from the battery, without any of the charge leaving the plates, (a) A voltmeter reads 45.0 V when placed across the capacitor. When a dielectric is inserted between die plates, completely filling the space, the voltmeter reads 11.5 V. What is the dielectric constant of the material? (b) What will the voltmeter read if the dielectric is now pulled away out so it fills only one-third of the space between the plates?arrow_forwardA capacitor is constructed from two square, metallic plates of sides and separation d. Charges +Q and Q are placed on the plates, and the power supply is then removed. A material of dielectric constant K is inserted a distance x into the capacitor as shown in Figure P20.85. Assume d is much smaller than x. (a) Find the equivalent capacitance of the device. (b) Calculate the energy stored in the capacitor. (c) Find the direction and magnitude of the force exerted by the plates on the dielectric. (d) Obtain a numerical value for the force when x = /2, assuming = 5.00 cm, d = 2.00 mm, the dielectric is glass ( = 4.50), and the capacitor was charged to 2.00 103 V before the dielectric was inserted. Suggestion: The system can be considered as two capacitors connected in parallel. Figure P20.85arrow_forward
- A capacitor is made from two flat parallel plates placed 0.40 mm apart. When a charge of 0.020C is placed oil the plates the potential difference between them is 250 V. (a) What is the capacitance of the plates? (b) What is the area of each plate? (c) What is the charge on the plates when the potential difference between them is 500 V? (d) What maximum potential difference can be applied between the plates so that the magnitude of electrical fields between the plates does not exceed 3.0 MV/m?arrow_forwardA parallel-plate capacitor is connected to a battery. What happens to the stored energy if the plate separation is doubled while the capacitor remains connected to the battery? (a) It remains the same, (b) It is doubled. (c) It decreases by a factor of 2. (d) It decreases by a factor of 4. (e) It increases by a factor of 4.arrow_forwardConsider the combination of capacitors in Figure P16.42. (a) Find the equivalent single capacitance of the two capacitors in series and redraw the diagram (called diagram 1) with this equivalent capacitance. (b) In diagram 1, find the equivalent capacitance of the three capacitors in parallel and redraw the diagram as a single battery and single capacitor in a loop. (c) Compute the charge on the single equivalent capacitor. (d) Returning to diagram 1, compute the charge on each individual capacitor. Does the sum agree with the value found in part (c)? (e) What is the charge on the 24.0-F capacitor and on the 8.00-F capacitor? Compute the voltage drop across (f) the 24.0-F capacitor and (g) the 8.00-F capacitor. Figure P16.42arrow_forward
- Unreasonable Results (a) An 8.00 F capacitor is connected in parallel to another capacitor, producing a total capacitance of 5.00 F. What is the capacitance of the second capacitor? (b) What is unreasonable about this result? (C) Which assumptions are unreasonable or inconsistent?arrow_forwardA nervous physicist worries that the two metal shelves of his wood frame bookcase might obtain a high voltage if charged by static electricity, perhaps produced by friction. (a) What is the capacitance of the empty shelves if they have area 1.00102 m2 and are 0.200 m apart? (b) What is the voltage between them it opposite charges of magnitude 2.00 nC are placed on them? (C) To show that this voltage poses a small hazard, calculate the energy stored.arrow_forwardA long thin wire is used in laser printers to charge the photoreceptor before exposure to light. This is done by applying a large potential difference between the wire and the photoreceptor. a. Use Equation 26.23, V(r)=20lnRr to determine a relationship between the electric potential V and the magnitude of the electric field E at a distance r from the center of the wire of radius R (r R). b. Determine the electric potential at a distance of 2.0 mm from the surface of a wire of radius R = 0.80 mm that will produce an electric field of 1.8 106 V/m at that point.arrow_forward
- Physics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage LearningCollege PhysicsPhysicsISBN:9781285737027Author:Raymond A. Serway, Chris VuillePublisher:Cengage Learning
- Physics for Scientists and Engineers, Technology ...PhysicsISBN:9781305116399Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningCollege PhysicsPhysicsISBN:9781305952300Author:Raymond A. Serway, Chris VuillePublisher:Cengage LearningPhysics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning