Concept explainers
(a)
The base and the collector current in each of the transistor. Also, the power dissipation in the gate.
(a)

Answer to Problem 17.12EP
The currents in the transistors are,
Explanation of Solution
Calculation:
The given diagram is shown in Figure 1
The expression to determine the value of the voltage
Substitute
The expression to determine the value of the current
Substitute
The conversion from
The conversion from
The second transistor and the output transistor are in cut off region and the current in the circuit are given by,
The expression for the value of the collector current and the base current of the output transistor is given by,
The expression for the base and the collector current of the third and the fourth transistor are given by,
The expression for the power dissipated in the circuit is given by,
Substitute
Conclusion:
Therefore, the currents in the transistors are,
(b)
The base and the collector current in each of the transistor. Also, the power dissipation in the gate.
(b)

Answer to Problem 17.12EP
The currents in the transistors are,
Explanation of Solution
Calculation:
The expression to determine the value of the voltage
Substitute
The expression for the voltage
Substitute
The expression to determine the value of the current
Substitute
The expression to determine the value of the current
Substitute
The conversion from
The conversion from
The expression for the base current of the second transistor is given by,
Substitute
The expression for the collector current of the second transistor is given by,
Substitute
The fifth transistor is in the cut off region and the current in the circuit are given by,
The expression for the value of the collector current of output transistor is given by,
Substitute
The expression for the base and the collector current of the third and the fourth transistor are given by,
The expression for the power dissipated in the circuit is given by,
Substitute
The conversion from
The conversion from
Conclusion:
Therefore, the currents in the transistors are,
Want to see more full solutions like this?
Chapter 17 Solutions
MICROELECT. CIRCUIT ANALYSIS&DESIGN (LL)
- I have uploaded the rules, please explain step by step and which rule you have appliedarrow_forwardUsing the CCS Compiler method to solve this question Write a PIC16F877A program that flash ON the 8-LED's connected to port-B by using two switches connected to port-D (Do & D₁) as shown in figure below, according to the following scenarios: (Hint: Use 500ms delay for each case with 4MHz frequency) 1. When Do=1 then B₁,B3,B7 are ON. 2. When Do 0 then Bo,B2, B4, B5, B6 are ON. 3. When D₁=1 then B4,B,,B6,B7 are ON. 4. When D₁-0 then Bo,B1,B2,B3 are ON.arrow_forwardUse the ramp generator circuit in Fig. B2a to generate the waveform shown in Fig. B2b. Write four equations relating resistors R1, R2, R3, capacitor C and voltages Vs, VR and VA.to the waveform parameters T₁, T, Vcm and Vm- If R = R2 = R3, R₁ = 2R, C = 1 nF, Vcm = 2 V and Vm = 1 V, T₁ = 2 μs and T = 10 μs solve for the values of R, Vs, VR and VA using your equations from part a(i). VR C +VA R3 V₂ Vo мат R1 VsO+ V₁ R₂ Figure B2a Vout Vcm+Vm Vcm Vcm-Vm 0 T₁ T 2T time Figure B2barrow_forward
- The circuit in Figure B1a is a common analogue circuit block. Explain why you would need such a circuit. Draw another circuit in which you use the current flowing in this loop to bias a common source amplifier. This circuit is not ideal for standard CMOS technologies due to threshold shift. Why? Draw an improved version of this circuit to make it better. VDD (W)P MA M3. (), REF (쁜)~ M₁ M2 lout 시~ Rsarrow_forward23bcarrow_forwardDraw the small-signal equivalent circuit of a single transistor amplifier given in figure B1b. Assume the current source to be ideal. Determine the Open-loop transfer function, pole frequency and gain-bandwidth product all in terms of transistor parameters 9m, To and CL. If the load capacitance is 1pF and the necessary unity gain frequency is 600MHz, find the gm for this transistor. V₁ V₁ CLarrow_forward
- Delmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage Learning
