Explanation Given data: Refer to the circuit Figure 16.91 in the textbook. Calculation: Consider the formula to find the capacitive reactance. X C = 1 s C Then, for the capacitor 10 pF . X 10 pF = 1 s 10 × 10 − 12 X 10 pF = 10 11 s Ω And for the capacitor 20 pF . X 20 pF = 1 s 20 × 10 − 12 X 20 pF = 0.05 × 10 12 s X 20 pF = 5 × 10 10 s Ω Re-draw the circuit as shown in below Figure 1 in s -domain . From the Figure 1, the voltages V a , V b , V c and V o are equal. V a = V b = V c = V o Write the nodal equation at node b . V b − V d 60 k + V b 5 × 10 10 s + 0 = 0 V o − V d 60 k + s V o 5 × 10 10 + 0 = 0 { ∵ V b = V o } V d 60 k = V o ( 1 60 k + s 5 × 10 10 ) = 0 V d = ( 1 + 60 × 10 3 s 5 × 10 10 ) V o Reduce the equation as follows. V d = ( 1 + 1.2 × 10 − 6 s ) V o (1) Write the nodal equation at node d . V d − V s 60 × 10 3 + V d − V c 10 11 s + V d − V b 60 × 10 3 = 0 V d − V s 60 × 10 3 + s ( V d − V o ) 10 11 + V d − V o 60 × 10 3 = 0 { ∵ V b = V c = V o } V d 60 × 10 3 − V s 60 × 10 3 + s V d

EE 98: Fundamentals of Electrical Circuits - With Connect Access

6th Edition

ISBN: 9781259981807

Author: Alexander

Publisher: MCG

See similar textbooks

Videos

Question

Chapter 16, Problem 68P

To determine

Find the transfer function VoVs for the op amp circuit in Figure 16.91.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 16, Problem 67P

Chapter 16, Problem 69P

Students have asked these similar questions

Q2: (33 Marks) Design FBD for manufacturing system where a conveyor belt is used to move a cart through a tunnel for processing. The process begins when a worker presses a start push button located at the start of the conveyor. Once the start push button is pressed, the cart moves forward along the conveyor belt and enters the tunnel. When the cart reaches the end of the tunnel, it stops automatically and remains in place for 10-minutes to complete a required operation, such as cooling or drying. After the 10-minute delay, the cart automatically returns to the starting point where the worker is stationed. The system then waits for the worker to press the start push button again, at which point the process is repeated. Start PBO Stop PBO LSI 0 LS 2 Motor

1. Find the resolution, current and output voltage for a binary weighted resistor DAC of (applied binary word is (locoj), the resistor values R = 12 kQ, Rf = 6 k2 and VR = 12 V. 2. Convert the following 5-bit digital values (ble 10) to analog, using the R-2R ladder. Assume that the Vs = 10 V, R = Rf = 7 ks

K Q4/ For the unity-feedback system where G(s) = do the following: a. Plot the Nyquist diagram. (S+2)(S+4)(S+6) b. Use your Nyquist diagram to find the range of gain, K, for stability

Chapter 16 Solutions

EE 98: Fundamentals of Electrical Circuits - With Connect Access

Ch. 16.2 - Determine vo(t) in the circuit of Fig. 16.6,...Ch. 16.2 - Prob. 2PP Ch. 16.2 - Prob. 3PP Ch. 16.3 - For the circuit shown in Fig. 16.12 with the same...Ch. 16.3 - Prob. 5PP Ch. 16.3 - The initial energy in the circuit of Fig. 16.17 is...Ch. 16.4 - Prob. 7PP Ch. 16.4 - Prob. 8PP Ch. 16.4 - Prob. 9PP Ch. 16.5 - Obtain the state variable model for the circuit...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Find the transfer function V o V s for the op amp circuit in Figure 16.91.

Solution Summary: The author explains how to find the transfer function for the op amp circuit in Figure 16.91.

Videos

Find the transfer function VoVs for the op amp circuit in Figure 16.91.

Want to see the full answer?

Chapter 16 Solutions