Explanation Write the energy rate balance equation for one inlet and one outlet system. [ Q ˙ 1 + W ˙ 1 + m ˙ ( h 1 + V 1 2 2 + g z 1 ) ] − [ Q ˙ 2 + W ˙ 2 + m ˙ ( h 2 + V 2 2 2 + g z 2 ) ] = Δ E ˙ system (I) Here, the rate of heat transfer is Q ˙ , the rate of work transfer is W ˙ , the enthalpy is h and the velocity is V , the gravitational acceleration is g , the elevation from the datum is z and the rate of change in net energy of the system is Δ E ˙ system ; the suffixes 1 and 2 indicates the inlet and outlet of the system. Consider the nozzle operates at steady state. Hence, the rate of change in net energy of the system becomes zero. Δ E ˙ system = 0 Since, the gas passes through the adiabatic nozzle, the heat transfer rate is negligible i.e. Q ˙ = 0 . Also neglect the work transfer rates i.e. W ˙ = 0 . The inlet, outlet are at same elevation, the potential energy becomes negligible i.e. g z = 0 . The Equations (I) reduced as follows to obtain the exit velocity. [ 0 + 0 + m ˙ ( h 1 + V 1 2 2 + 0 ) ] − [ 0 + 0 + m ˙ ( h 2 + V 2 2 2 + 0 ) ] = 0 m ˙ ( h 1 + V 1 2 2 ) − m ˙ ( h 2 + V 2 2 2 ) = 0 m ˙ ( h 1 + V 1 2 2 ) = m ˙ ( h 2 + V 2 2 2 ) h 1 + V 1 2 2 = h 2 + V 2 2 2 V 2 2 2 − V 1 2 2 = h 1 − h 2 V 2 2 − V 1 2 = 2 ( h 1 − h 2 ) V 2 = V 1 2 + 2 ( h 1 − h 2 ) (II) It is given that the initial velocity is low. Hence, neglect the initial velocity i.e. V 1 = 0 . Substitute 0 for V 1 in Equation (II). V 2 = ( 0 ) 2 + 2 ( h 1 − h 2 ) = 2 ( h 1 − h 2 ) (III) Write formula for enthalpy departure factor ( Z h ) . Z h = ( h ¯ ideal − h ¯ ) T , P R u T cr (IV) Here, the molar enthalpy at ideal gas state is h ¯ ideal , the molar enthalpy and normal state is h ¯ , the universal gas constant is R u , and the critical temperature is T cr ; The subscripts T , P indicates the correspondence of given temperature and pressure. Rearrange the Equation (I) to obtain h ¯ . h ¯ = h ¯ ideal − Z h R u T cr (V) Refer Equation (V) express as two states of enthalpy difference (initial–final). h ¯ 1 − h ¯ 2 = ( h ¯ 1 − h ¯ 2 ) ideal − ( Z h 1 − Z h 2 ) R u T cr (VI) Here, the molar enthalpy difference is h ¯ 2 − h ¯ 1 . The enthalpy difference is expressed as follows. h 1 − h 2 = h ¯ 1 − h ¯ 2 M CO 2 (VII) Refer Table A-1, “Molar mass, gas constant, and critical-point properties”

9th Edition

ISBN: 9781307573022

Author: CENGEL

Publisher: MCG/CREATE

See similar textbooks

Videos

Question

Chapter 12.6, Problem 75P

To determine

The exit velocity of the carbon dioxide using generalized enthalpy departure chart.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 12.6, Problem 74P

Chapter 12.6, Problem 77P

Students have asked these similar questions

1- Determine the following: 1- RSHF? 2- C.C.C in tons-ref. 3- Mass of supply air? Fresh Spray chilled water S air 100% RH To 34 C db & 26 wbt S Operation fan room I Exhaust air Ti 22 C db & 50% RH

How do I solve this task A weight for a lift is suspended using an adapter. The counterweight is held up with 4 screws. The weight F is 3200kg. The screws have a strength class of 8.8. Safety factor 3 Which is the smallest bunch size that can be used?+_Sr/Fm =0,16Gr=0,71ơ=800·0.8=640 MPaAs=?Fmax= As·ơ·GrFs=ơs·AsFFm= Fs· GFSF =SF / FFm · FFm Fpreload =Fload / SF → Fload /3Fpreload per screw =Fload / SF → Fload /4As=Fpreload per screw /ơ·Gr → As= Fpreload per screw / 640· 0.71 The correct answer should be M12 with As=84.3mm²

... TELEGRAM ديسمبر ۲۰۲ عند الساعة سوأل الوجه البينة ۲۷ - Find the equivalent resistance between A and B bellows For the circuit shown. • All resistances in Ohms. 2 C 2 A 4 B www 4 E 5 www ww 8 bar K. Dr. Abduljabbo Hammade 27/12/2024

Chapter 12 Solutions

THERMODYNAMICS-SI ED. EBOOK >I<

Ch. 12.6 - What is the difference between partial...Ch. 12.6 - Consider the function z(x, y). Plot a differential...Ch. 12.6 - Consider a function z(x, y) and its partial...Ch. 12.6 - Prob. 4P Ch. 12.6 - Prob. 5P Ch. 12.6 - Consider a function f(x) and its derivative df/dx....Ch. 12.6 - Conside the function z(x, y), its partial...Ch. 12.6 - Consider air at 350 K and 0.75 m3/kg. Using Eq....Ch. 12.6 - Consider air at 350 K and 0.75 m3/kg. Using Eq....Ch. 12.6 - Nitrogen gas at 800 R and 50 psia behaves as an...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

The exit velocity of the carbon dioxide using generalized enthalpy departure chart.

Solution Summary: The author explains the exit velocity of the carbon dioxide using generalized enthalpy departure chart and the energy rate balance equation for one inlet and one outlet system.

Videos

The exit velocity of the carbon dioxide using generalized enthalpy departure chart.

Want to see the full answer?

Chapter 12 Solutions