Concept explainers
A curve in a speed track has a radius of 1000 ft and a rated speed of 120 mi/h. (See Sample Prob. 12.7 for the definition of rated speed.) Knowing that a racing car starts skidding on the curve when traveling at a speed of 180 mi/h, determine (a) the banking angle θ, (b) the coefficient of static friction between the tires and the track under the prevailing conditions, (c) the minimum speed at which the same car could negotiate the curve.
Fig. P12.52
(a)
Find the banking angle
Answer to Problem 12.52P
The banking angle
Explanation of Solution
Given information:
The radius
The rated speed
The frictional force
The speed (v) at prevailing condition is 180 mi/h.
Calculation:
Write the general equation weight (W).
Here, m is the mass and g is the acceleration due to gravity.
Write the general equation of acceleration (a) in curved path.
Here, v is the speed and
Sketch the free body diagram and kinetic diagram of the racing car as shown in Figure (1).
Refer Figure (1):
Consider the racing car moves at rated speed.
Find the banking angle
Apply Newton’s law of equation along x-axis.
Substitute 0 for
Substitute 120 mi/h for
Thus, the banking angle
(b)
Find the coefficient of static friction between the tires and the track under the prevailing conditions.
Answer to Problem 12.52P
The coefficient of static friction between the tires and the track under the prevailing conditions is
Explanation of Solution
Calculation:
Refer Figure (1):
Consider the racing car moves in prevailing condition.
Apply Newton’s law of equation along y-axis.
Substitute
Apply Newton’s law of equation along y-axis.
Substitute
Find the coefficient of static friction
Write the general equation of normal force(N).
Substitute Equation (1) and (2) in Equation (3).
Substitute 180 mi/h for v,
Thus, the coefficient of static friction between the tires and the track under the prevailing conditions is
(c)
Find the minimum speed at which the same car could negotiate that curve.
Answer to Problem 12.52P
The minimum speed at which the same car could negotiate that curve is
Explanation of Solution
Calculation:
Write the general equation of normal force (N) in minimum speed.
Substitute Equation (1) and (2) in Equation (3).
Substitute 0.390 for
Thus, the minimum speed at which the same car could negotiate that curve is
Want to see more full solutions like this?
Chapter 12 Solutions
VEC MECH 180-DAT EBOOK ACCESS(STAT+DYNA)
- use momentum and impulse equation.arrow_forwardThe block B start from rest and slides on the 30 wedge A , which is supported by a horizontal surface . Neglecting frictionarrow_forwardTo transport a series of bundles of shingles A to a roof, a contractor uses a motor-driven lift consisting of a horizontal platform BC which rides on rails attached to the sides of a ladder. The lift starts from rest and initially moves with a D constant acceleration a1 as shown. The lift then decelerates at a constant rate a2 and comes to rest at D, near the top of the ladder. Knowing that the coefficient of static friction between a bundle of shingles and the horizontal platform is 0.30, determine the largest allowable acceleration a1 and the largest allowable deceleration az if the bundle is not to slide on the platform. 4.4 m 65° A B 0.8 marrow_forward
- An automobile weighing 4000 lb is driven down a 5° incline at a speed of 60 mih when the brakes are applied, causing a constant total braking force (applied by the road on the tires) of 1500 Ib. Determine the time required for the automobile to come to a stop.arrow_forwardA truck is traveling down a road with a 4-percent grade at a speed of 60 mi/h when its brakes are applied to slow it down to 20 mi/h. An antiskid braking system limits the braking force to a value at which the wheels of the truck are just about to slide. Knowing that the coefficient of static friction between the road and the wheels is 0.60, determine the shortest time needed for the truck to slow down.arrow_forwardRequired information A uniform thin bar AB of length L = 5.5 ft is released from rest at an angle 0 = 0₁. As the bar slides, the ends A and B maintain contact with the surfaces on which they slide. A L B Neglecting friction and knowing that the end A has a speed of 18 ft/s right before hitting the floor, determine 0₁. The value of 0₁ isarrow_forward
- To transport a series of bundles of shingles A to a roof, a contractor uses a motor-driven lift consisting of a horizontal platform BC which rides on rails attached to the sides of a ladder. The lift starts from rest and initially moves with a constant acceleration a1 as shown. The lift then decelerates D at a constant rate a2 and comes to rest at D, near the top of the ladder. Knowing that the coefficient of static friction 4.4 m between a bundle of shingles and the horizontal platform is 0.30, determine the largest allowable acceleration a1 and the largest allowable deceleration az if the bundle is not to slide on the platform. aj 65° A В 0.8 marrow_forward3. A small block B fits inside a lot cut in arm OA which rotates in a vertical plane at a constant rate. The block remains in contact with the end of the slot closest to A and its speed is 1.4 m/s for 0< 0 <150°. Knowing that the block begins to slide when 0 = 150°, determine the coefficient of static friction between the block and the slot. V = 0.3 m Aarrow_forwardTwo blocks having the weights and position shown, rest on a frame which rotates about its vertical axis at a constant speed. The coefficient of friction between the blocks and the frame is 0.02 neglecting the weight and friction of the pulley, at what speed in RPM will the blocks start to slide? What is the tension in the cord at this instant.?arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY