
Interpretation:
The value of constants n and c for the given equation needs to be calculated.
Concept Introduction:
At constant temperature, the determinationof solid phase transformation is done by using the Avarmi equation. Generally, it is used to describe the rate of kinetic crystallization.
This equation is also known as the JMAK equation as it was founded by Johnson-Mehl-Avrami-Kolmology. This equation was first found in the year

Answer to Problem 12.4P
The value of
Explanation of Solution
Given:
Eqauation:
Temperature =
Assume -
Elapsed time −
Temperature constants -
The effect of temperature on crystallization is:
Fig.
To calculate the constants value of c and n by using the below formula,
Taking natural logarithm on both sides,
From the given equations of curves, the values are:
Table
From above table, plot the solpe of the graph:
Fig.
Equation of a straight line −
Then to find the value of n,
Then to find value of
The value of c and n are
Want to see more full solutions like this?
Chapter 12 Solutions
Essentials Of Materials Science And Engineering
- "Please, the answer must be documented from a book, experience, or accurate information without using artificial intelligence." Suppose you have two push buttons connected to pins 7 & 8 and two LED's connected to pins 9 & 10 of an Arduino. Write a program to turn ON the LED's if the two push buttons are pressed according to the following scenario. push buttons push buttons LED (pin9) LED (pin10) Delay (pin7) (pin8) open open HIGH HIGH 2s closed open LOW HIGH 1s open closed HIGH LOW 1s closed closed LOW LOW 3sarrow_forward"Please, the answer must be documented from a book, experience, or accurate information without using artificial intelligence." OF ENG Connect 8 LED's and one push button to an Arduino, write a program to glow the LED's in series one by one when the button is pressed. When the button is released it should stop and restart again when the button is pressed hold. And when the LED's sequence is complete it should stop and shouldn't restart unless the button is released and repressed.arrow_forwardBars AD and CE (E=105 GPa, a = 20.9×10-6 °C) support a rigid bar ABC carrying a linearly increasing distributed load as shown. The temperature of Bar CE was then raised by 40°C while the temperature of Bar AD remained unchanged. If Bar AD has a cross-sectional area of 200 mm² while CE has 150 mm², determine the following: the normal force in bar AD, the normal force in bar CE, and the vertical displacement at Point A. D 0.4 m -0.8 m A -0.4 m- B -0.8 m- E 0.8 m C 18 kN/marrow_forward
- "Please, the answer must be documented from a book, experience, or accurate information without using artificial intelligence." Write an Arduino program to read the status of two push buttons COLED's connected to pins 2&3 respectively and flash ON two connected to pins 12&13 respectively according to the following scenario: If pin 2 is HIGH let LED 12 flash with delay of 400ms, and if pin 3 HIGH, let LED 13 flash ON with delay of 300ms.arrow_forward"Please, the answer must be documented from a book, experience, or accurate information without using artificial intelligence." Write an Arduino program that flash ON the 4-LED's by using two switches according to the following scenarios: 1. when S₁=1 then L3, L4 are ON. 2. when S₁=0 then L1,L2 are ON. 3. when S2=1 then L2,L4 are ON. 4. when S2-0 then L₁,L3 are ON. 140arrow_forward"Please, the answer must be documented from a book, experience, or accurate information without using artificial intelligence." Write an Arduino program to obtain the complement following input sequence (1011) by using switch connected to pin11 and one LED connected to pin12. one push of the buttonarrow_forward
- "Please, the answer must be documented from a book, experience, or accurate information without using artificial intelligence." Suppose you have two push buttons connected to pins 7,8 and two LED's connected to pins 9,10 of an Arduino. Write a program to turn ON/OFF the LED's if the two push buttons are pressed according to the following scenarios: S7 S$ L9 L10 Delay 0 0 1 1 2s 1 0 0 1 1s 1 1 0 1s 0 0 3s EERINGarrow_forward(read image)arrow_forwardBoth circuit do it multisim okk don't use guidelines will dislike okkarrow_forward
- Problem 3.30 A piston-cylinder device contains 0.85 kg of refrigerant- 134a at -10°C. The piston that is free to move has a mass of 12 kg and a diameter of 25 cm. The local atmospheric pressure is 100 kPa. Now, heat is transferred to refrigerant-134a until the temperature is 15°C. Determine (a) the final pressure, (b) the change in the volume of the refrigerant, and (c) the change in the enthalpy of the refrigerant-134a. please show Al work step by steparrow_forwardPart 1 The storage tank contains lubricating oil of specific gravity 0.86 In one inclined side of the tank, there is a 0.48 m diameter circular inspection door, mounted on a horizontal shaft along the centre line of the gate. The oil level in the tank rests 8.8 m above the mounted shaft. (Please refer table 01 for relevant SG, D and h values). Describe the hydrostatic force and centre of pressure with the aid of a free body diagram of the inspection door. Calculate the magnitude of the hydrostatic force and locate the centre of pressure. 45° Estimate the moment that would have to be applied to the shaft to open the gate. Stop B If the oil level raised by 2 m from the current level, calculate the new moment required to open the gate. Figure 01arrow_forwardFrom thermodynamics please fill in the table show all work step by steparrow_forward
- MATLAB: An Introduction with ApplicationsEngineeringISBN:9781119256830Author:Amos GilatPublisher:John Wiley & Sons IncEssentials Of Materials Science And EngineeringEngineeringISBN:9781337385497Author:WRIGHT, Wendelin J.Publisher:Cengage,Industrial Motor ControlEngineeringISBN:9781133691808Author:Stephen HermanPublisher:Cengage Learning
- Basics Of Engineering EconomyEngineeringISBN:9780073376356Author:Leland Blank, Anthony TarquinPublisher:MCGRAW-HILL HIGHER EDUCATIONStructural Steel Design (6th Edition)EngineeringISBN:9780134589657Author:Jack C. McCormac, Stephen F. CsernakPublisher:PEARSONFundamentals of Materials Science and Engineering...EngineeringISBN:9781119175483Author:William D. Callister Jr., David G. RethwischPublisher:WILEY





