During major windstorms, high vehicles such as RVs and semis may be thrown off the road and boxcars off their tracks, especially when they are empty and in open areas. Consider a 6000-kg semi that is
10 m long, 2.5 m high, and 2 in wide. The distance between the bottom of the truck and the road is 0.8 in. Now the truck is exposed to winds from its side surface. Determine the wind velocity that will tip the truck over to its side. Take the air density to be 1.1 kg/m3 and assume the weight to be uniformly distributed.
The wind velocity that will tip the truck over to its side.
Answer to Problem 43P
The wind velocity that will tip the truck over to its side is
Explanation of Solution
Given information:
The mass of the truck is
Write the expression of weight of the truck.
Here, the mass of the truck is
Write the expression of frontal area.
Here, the length of the truck is
The below figure represent the forces acting on the truck.
Figure-(1)
Write the expression of equilibrium of momentum about point
Here, the width of the truck is
Refer table 11.2 "Representative drag coefficient
Write the expression of drag force acting on the truck.
Here, the density of the air is
Write the expression of characteristics length of the truck.
Here, the perimeter of the truck is
Write the expression of perimeter of the truck.
Write the expression of Reynolds number.
Here, the kinematic viscosity is
Calculation:
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Refer table A-9 "Properties of air" to find the value of kinematic viscosity of air as
Substitute
So, the Equation used for
Conclusion:
The wind velocity that will tip the truck over to its side is
Want to see more full solutions like this?
Chapter 11 Solutions
FLUID MECHANICS FUNDAMENTALS+APPS
- Access Pearson Mastering Engineering Back to my courses Course Home Course Home Scoresarrow_forwardAccess Pearson Mastering Engineering Back to my courses Course Home Course Home Scores Review Next >arrow_forwardAccess Pearson Course Home Scoresarrow_forwardCan you answer this question?arrow_forwardCan you answer this question?arrow_forwardA gear has a gear wheel with 16 teeth. The gear should be dimensioned for the highest and lowest gear ratio. Looking for output power, torque, speed?nin= 2000 rpmmin = 30Nmn=0,9a max= 450 mmModule 4Gear limitsz1 z213 13-1614 14-2615 15-4516 16-10117 17-131418 18-…..I have calculate but I can’t get the right answers…..√16 =459x60/56x57=1.1 lowest59x60/13x13=20,94 highestnut=2000/1.1= 1818rpmnut=2000/20.94=95.5 rpmMut=1.1x30=33 NmMut=20.94x30=628,2 Nm(Right answer)LowestZ=13, M=24,4Nm, n=2462 rpmHighestZ=92, M=172,5Nm, n=347,8 rpmP=5655W on botharrow_forwardarrow_back_iosSEE MORE QUESTIONSarrow_forward_ios
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY