FLUID MECHANICS FUNDAMENTALS+APPS
FLUID MECHANICS FUNDAMENTALS+APPS
4th Edition
ISBN: 2810022150991
Author: CENGEL
Publisher: MCG
bartleby

Videos

Question
Book Icon
Chapter 11, Problem 110P
To determine

The error involved for each case and asses the accuracy of strokes law.

Expert Solution & Answer
Check Mark

Answer to Problem 110P

In first ball 9.375% error is involved.

In second ball 10.156% error is involved.

In third ball 4.3% error is involved.

Explanation of Solution

Given information:

The diameter of the first aluminum ball is 2mm, the diameter of the second aluminum ball is 4mm, the diameter of the third aluminum ball is 10mm, the density of aluminum ball is 2600kg/m3, the temperature of glycerin is 22°C, the density of the glycerin is 1274kg/m3, the dynamic viscosity of glycerin is 1kg/ms, terminal setting velocity of the first ball is 3.2mm/s, the terminal velocity of second ball is 12.8mm/s and the terminal velocity of third ball is 60.4mm/s.

Write the expression of drag force acting on the freely falling body.

  FD=WFB...... (I)

Here, the weight of the ball is W and the bouncy force is FB.

Write the expression of drag force by strokes law.

  FD=3πVD+(9π16)ρV2D2...... (II)

Here, the terminal velocity is V, the diameter of the ball is D and the density of the fluid is ρ.

Write the expression of the weight of the body.

  W=ρsgV1...... (III)

Here, the density of the ball is ρs, the acceleration due to gravity is g and the volume of the ball is V1.

Write the expression of bouncy force applied by a body.

  FB=ρgV1...... (IV)

Here, the density of the fluid is ρ.

Substitute 3πVD+(9π16)ρV2D2 for FD, ρgV1 for FB and ρsgV1 for W in Equation (I).

  3πVD+( 9π 16)ρV2D2=ρsgV1ρgV1(3πD)V+( 9πρ D 2 16)V2=gV1(ρsρ)( 9πρ D 2 16)V2+(3πD)VgV1(ρsρ)=0...... (V)

Write the expression of volume of the ball.

  V1=πD36...... (VI)

Write the expression of percentage error.

  Error=(VgVVg)×100...... (VII)

Here, the given terminal velocity is Vg.

Calculation:

For First ball,

Substitute 2mm for D in Equation (VI).

  V1=π ( 2mm )36=π { ( 2mm )×( 1m 1000mm )}36=π×8× 10 96m3=4.189×109m3

Substitute 1274kg/m3 for ρ, 2600kg/m3 for ρs, 9.81m/s2 for g 2mm for D and 4.189×109m3 for V1 in Equation (V).

[ { 9π×( 1274 kg/ m 3 )× ( 2mm ) 2 16 } V 2 +{ 3π( 2mm ) }V ( 9.81 m/s 2 )×( 4.189× 10 9 m 3 )×{ ( 2600 kg/ m 3 )( 1274 kg/ m 3 ) } ]=0

[ { 9π×( 1274 kg/ m 3 )× { ( 2mm )×( 1m 1000mm ) } 2 16 } V 2 +{ 3π( 2mm )×( 1m 1000mm ) }V[ ( 9.81 m/s 2 )×( 4.189× 10 9 m 3 ) ×{ ( 2600 kg/ m 3 )( 1274 kg/ m 3 ) } ] ]=0

[ ( 9.005× 10 3 kg/m ) V 2 +( 0.0188m )V( 5.3455× 10 4 kgm/s 2 ) ]=0

V= [ ( 0.0188m )± ( 0.0188m ) 2 { 4×( 9.005× 10 3 kg/m )×{ ( 5.3455× 10 4 kgm/s 2 ) } } ] 2×( 9.005× 10 3 )

Taking positive sign.

  V=[( 0.0188m)+ ( 0.0188m ) 2 { 4×( 9.005× 10 3 kg/m )×{ ( 5.3455× 10 4 kgm/s 2 )}} ]2×( 9.005× 10 3 kg/m )=0.0029m/s

Taking Negative sign.

  V=[( 0.0188m) ( 0.0188m ) 2 { 4×( 9.005× 10 3 kg/m )×{ ( 5.3455× 10 4 kgm/s 2 )}} ]2×( 9.005× 10 3 kg/m )=2.8967m/s

Here, the negative value of velocity is not desirable so the velocity is 0.0029m/s.

Substitute 0.0029m/s for V and 3.2mm/s for Vg in Equation (VII).

  Error={( 3.2 mm/s )( 0.0029m/s )( 3.2 mm/s )}×100={( 3.2 mm/s )×( 1m 1000mm )( 0.0029m/s )( 3.2 mm/s )×( 1m 1000mm )}×100={( 0.0032m/s )( 0.0029m/s )( 0.0032m/s )}×100=9.375%

In first ball 9.375% error is involved.

For Second ball,

Substitute 4mm for D in Equation (VI).

  V1=π ( 4mm )36=π { ( 4mm )×( 1m 1000mm )}36=π×6.4× 10 86m3=3.35×108m3

Substitute 1274kg/m3 for ρ, 2600kg/m3 for ρs, 9.81m/s2 for g 4mm for D and 3.35×108m3 for V1 in Equation (V).

[ { 9π×( 1274 kg/ m 3 )× ( 4mm ) 2 16 } V 2 +{ 3π( 4mm ) }V ( 9.81 m/s 2 )×( 3.35× 10 8 m 3 )×{ ( 2600 kg/ m 3 )( 1274 kg/ m 3 ) } ]=0

[ { 9π×( 1274 kg/ m 3 )× { ( 4mm )×( 1m 1000mm ) } 2 16 } V 2 +{ 3π( 4mm )×( 1m 1000mm ) }V[ ( 9.81 m/s 2 )×( 3.35× 10 8 m 3 ) ×{ ( 2600 kg/ m 3 )( 1274 kg/ m 3 ) } ] ]=0

[ ( 0.036 kg/m ) V 2 +( 0.03768m )V( 4.4× 10 4 kgm/s 2 ) ]=0

V= [ ( 0.0188m )± ( 0.03768m ) 2 { 4×( 0.036 kg/m )×{ ( 5.3455× 10 4 kgm/s 2 ) } } ] 2×( 0.036 kg/m )

Taking positive sign.

  V=[( 0.0188m)+ ( 0.03768m ) 2 { 4×( 0.036 kg/m )×{ ( 5.3455× 10 4 kgm/s 2 )}} ]2×( 0.036 kg/m )=0.0115m/s

Taking Negative sign.

  V=[( 0.0188m) ( 0.03768m ) 2 { 4×( 0.036 kg/m )×{ ( 5.3455× 10 4 kgm/s 2 )}} ]2×( 0.036 kg/m )=1.058m/s

Here, the negative value of velocity is not desirable so the velocity is 0.0115m/s.

Substitute 0.0115m/s for V and 12.8mm/s for Vg in Equation (VII).

  Error={( 12.8 mm/s )( 0.0115m/s )( 12.8 mm/s )}×100={( 12.8 mm/s )×( 1m 1000mm )( 0.0115m/s )( 12.8 mm/s )×( 1m 1000mm )}×100={( 0.0128m/s )( 0.0115m/s )( 0.0128m/s )}×100=10.156%

In second ball 10.156% error is involved.

For Third ball.

Substitute 10mm for D in Equation (VI).

  V1=π ( 10mm )36=π { ( 10mm )×( 1m 1000mm )}36=π×1× 10 66m3=5.235×107m3

Substitute 1274kg/m3 for ρ, 2600kg/m3 for ρs, 9.81m/s2 for g 10mm for D and 5.235×107m3 for V1 in Equation (V).

[ { 9π×( 1274 kg/ m 3 )× ( 10mm ) 2 16 } V 2 +{ 3π( 10mm ) }V ( 9.81 m/s 2 )×( 5.235× 10 7 m 3 )×{ ( 2600 kg/ m 3 )( 1274 kg/ m 3 ) } ]=0

[ { 9π×( 1274 kg/ m 3 )× { ( 10mm )×( 1m 1000mm ) } 2 16 } V 2 +{ 3π( 10mm )×( 1m 1000mm ) }V[ ( 9.81 m/s 2 )×( 5.235× 10 7 m 3 ) ×{ ( 2600 kg/ m 3 )( 1274 kg/ m 3 ) } ] ]=0

[ ( 0.225 kg/m ) V 2 +( 0.0942m )V( 0.0068 kgm/s 2 ) ]=0

V= [ ( 0.0942m )± ( 0.0942m ) 2 { 4×( 0.225 kg/m )×{ ( 0.0068 kgm/s 2 ) } } ] 2×( 0.225 kg/m )

Taking positive sign.

  V=[( 0.0942m)+ ( 0.0942m ) 2 { 4×( 0.225 kg/m )×{ ( 0.0068 kgm/s 2 )}} ]2×( 0.225 kg/m )=0.063m/s

Taking Negative sign.

  V=[( 0.0942m)+ ( 0.0942m ) 2 { 4×( 0.225 kg/m )×{ ( 0.0068 kgm/s 2 )}} ]2×( 0.225 kg/m )=0.48m/s

Here, the negative value of velocity is not desirable so the velocity is 0.063m/s.

Substitute 0.063m/s for V and 60.4mm/s for Vg in Equation (VII).

  Error={( 60.4 mm/s )( 0.063m/s )( 12.8 mm/s )}×100={( 60.4 mm/s )×( 1m 1000mm )( 0.063m/s )( 60.4 mm/s )×( 1m 1000mm )}×100={( 0.0604m/s )( 0.063m/s )( 0.0604m/s )}×100=4.3%

In third ball 4.3% error is involved.

Conclusion:

In first ball 9.375% error is involved.

In second ball 10.156% error is involved.

In third ball 4.3% error is involved.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
This is an old practice exam. Fce = 110lb and FBCD = 62 lb but why
Quiz/An eccentrically loaded bracket is welded to the support as shown in Figure below. The load is static. The weld size for weld w1 is h1 = 4mm, for w2 h2 = 6mm, and for w3 is h3 =6.5 mm. Determine the safety factor (S.f) for the welds. F=29 kN. Use an AWS Electrode type (E100xx). 163 mm S 133 mm 140 mm Please solve the question above I solved the question but I'm sure the answer is wrong the link : https://drive.google.com/file/d/1w5UD2EPDiaKSx3W33aj Rv0olChuXtrQx/view?usp=sharing
Q2: (15 Marks) A water-LiBr vapor absorption system incorporates a heat exchanger as shown in the figure. The temperatures of the evaporator, the absorber, the condenser, and the generator are 10°C, 25°C, 40°C, and 100°C respectively. The strong liquid leaving the pump is heated to 50°C in the heat exchanger. The refrigerant flow rate through the condenser is 0.12 kg/s. Calculate (i) the heat rejected in the absorber, and (ii) the COP of the cycle. Yo 8 XE-V lo 9 Pc 7 condenser 5 Qgen PG 100 Qabs Pe evaporator PRV 6 PA 10 3 generator heat exchanger 2 pump 185 absorber

Chapter 11 Solutions

FLUID MECHANICS FUNDAMENTALS+APPS

Ch. 11 - During flow over a given slender body such as a...Ch. 11 - What is terminal velocity? How is it determined?Ch. 11 - What is the difference between skin friction drag...Ch. 11 - What is the effect of surface roughness on the...Ch. 11 - Prob. 15CPCh. 11 - What is flow separation? What causes it? What is...Ch. 11 - Prob. 17CPCh. 11 - Consider laminar flow over a flat plate. How does...Ch. 11 - In general, how does the drag coefficient vary...Ch. 11 - Fairings are attached to the front and back of a...Ch. 11 - Prob. 21PCh. 11 - The resultant of the pressure and wall shear...Ch. 11 - Prob. 23PCh. 11 - Prob. 24PCh. 11 - To reduce the drag coefficient and thus to improve...Ch. 11 - A circular sign has a diameter of 50 cm and is...Ch. 11 - Prob. 28PCh. 11 - Prob. 29PCh. 11 - At highway speeds, about half of the power...Ch. 11 - A submarine can be treated as an ellipsoid with a...Ch. 11 - A 70-kg bicyclist is riding her 1 5-kg bicycle...Ch. 11 - A wind turbine with two or four hollow...Ch. 11 - During steady motion of a vehicle on a level road,...Ch. 11 - Prob. 37EPCh. 11 - A 0.80-m-diameter, 1 .2-rn-high garbage can is...Ch. 11 - An 8-mm-diameter plastic sphere whose density is...Ch. 11 - Prob. 40PCh. 11 - The drag coefficient of a vehicle increases when...Ch. 11 - To reduce the drag coefficient and thus to improve...Ch. 11 - During major windstorms, high vehicles such as RVs...Ch. 11 - What does the friction coefficient represent in...Ch. 11 - What fluid property is responsible for the...Ch. 11 - How is the average friction coefficient determined...Ch. 11 - Prob. 47EPCh. 11 - The local atmospheric pressure in Denver, Colorado...Ch. 11 - Prob. 50PCh. 11 - Prob. 51EPCh. 11 - Air at 25C and 1 atm is flowing over a long flat...Ch. 11 - Prob. 54PCh. 11 - During a winter day, wind at 70 km/h, 5C , and I...Ch. 11 - Prob. 56PCh. 11 - The forming section of a plastics plant puts out a...Ch. 11 - Prob. 58CPCh. 11 - Why is flow separation in flow over cylinders...Ch. 11 - Prob. 60CPCh. 11 - A 5-mm-diameter electrical transmission line is...Ch. 11 - A 1ong 5-cm-diameter steam pipe passes through...Ch. 11 - Consider 0.8-cm-diameter hail that is falling...Ch. 11 - Prob. 64EPCh. 11 - Prob. 65PCh. 11 - Prob. 66PCh. 11 - Prob. 67EPCh. 11 - One of the popular demonstrations in science...Ch. 11 - Prob. 69PCh. 11 - What is stall? What causes an airfoil to stall?...Ch. 11 - Prob. 71CPCh. 11 - Air is flowing past a symmetrical airfoil at zero...Ch. 11 - Both the lift and the drag of an airfoil increase...Ch. 11 - Prob. 74CPCh. 11 - Prob. 75CPCh. 11 - Air is flowing past a symmetrical airfoil at an...Ch. 11 - Prob. 77CPCh. 11 - Prob. 78CPCh. 11 - Prob. 79CPCh. 11 - Prob. 80CPCh. 11 - How do flaps affect the lift and the drag of...Ch. 11 - Prob. 82EPCh. 11 - Consider an aircraft that takes off at 260 km/h...Ch. 11 - Prob. 84PCh. 11 - Prob. 85PCh. 11 - A tennis ball with a mass of 57 and a diameter of...Ch. 11 - A small aircraft has a wing area of 40 m2, a lift...Ch. 11 - Prob. 89PCh. 11 - Consider a light plane that has a total weight of...Ch. 11 - A small airplane has a total mass of 1800 kg and a...Ch. 11 - An airplane has a mass of 48.000 k. a wins area of...Ch. 11 - Prob. 93EPCh. 11 - Prob. 94PCh. 11 - Prob. 95EPCh. 11 - A 2-zn-high, 4-zn-wide rectangular advertisement...Ch. 11 - 11-97 A plastic boat whose bottom surface can be...Ch. 11 - Prob. 99PCh. 11 - Prob. 100EPCh. 11 - A commercial airplane has a total mass of 150.000...Ch. 11 - Prob. 102PCh. 11 - Prob. 103PCh. 11 - Prob. 104PCh. 11 - Prob. 105PCh. 11 - Prob. 107PCh. 11 - Prob. 108PCh. 11 - Prob. 109PCh. 11 - Prob. 110PCh. 11 - Prob. 111PCh. 11 - Prob. 113PCh. 11 - Prob. 115PCh. 11 - Prob. 116PCh. 11 - Prob. 117PCh. 11 - Prob. 118PCh. 11 - Prob. 119PCh. 11 - The region of flow trailing the body where the...Ch. 11 - Prob. 121PCh. 11 - Prob. 122PCh. 11 - Prob. 123PCh. 11 - Prob. 124PCh. 11 - Prob. 125PCh. 11 - Prob. 126PCh. 11 - An airplane has a total mass of 3.000kg and a wing...Ch. 11 - Prob. 128PCh. 11 - Write a report on the history of the reduction of...Ch. 11 - Write a report oil the flips used at the leading...Ch. 11 - Discuss how to calculate drag force a unsteady...Ch. 11 - Large commercial airplanes cruise at high...Ch. 11 - Many drivers turn off their air conditioners and...Ch. 11 - Consider the boundary layer growing on a flat...
Knowledge Booster
Background pattern image
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
International Edition---engineering Mechanics: St...
Mechanical Engineering
ISBN:9781305501607
Author:Andrew Pytel And Jaan Kiusalaas
Publisher:CENGAGE L
Text book image
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Text book image
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Unit Conversion the Easy Way (Dimensional Analysis); Author: ketzbook;https://www.youtube.com/watch?v=HRe1mire4Gc;License: Standard YouTube License, CC-BY