Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)
8th Edition
ISBN: 9781305387102
Author: Kreith, Frank; Manglik, Raj M.
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 1, Problem 1.50P
A steam pipe 200 mm in diameter passes through a large basement room. The temperature of the pipe wall is 500°C, while that of the ambient air in the room is 20°C. Determine the heat transfer rate by convection and radiation per unit length of steam pipe if the emissivity of the pipe surface is 0.8 and the natural convection heat transfer coefficient has been determined to be 10
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
(b)
A transistor with a height of 0.4 cm and a diameter of 0.6 cm is mounted on a circuit board
as shown in Figure 3. The transistor is cooled by air flowing over it with an average heat
transfer coefficient of 30 W/m².K. If the air temperature is 55°C and the transistor case
temperature is not to exceed 70°C, determine the amount of power this transistor can
dissipate safely. Disregard any heat transfer from the transistor base.
Air
55°C
Power
transistor 0.6 cm
T, ≤ 70°C
-0.4 c
0.4 cm-
Figure 3
The temperature of a tank in the form of liquid nitrogen is -10 ° C. Tank diameter is 16 cm. The amount of heat lost by convection and radiation from the tank to the environment is 65.5 W / m. Calculate the temperature of the environment where the tank is located .h = 4.35 W / m2K, e= 1.
A person stands in a breezy room whose temperature is 20 °C. The emissivity of
the person is 0.35. Determine the total rate of heat transfer from this person if the
exposed surface area and the average surface temperature of the person are 1.6
m2 and 29 °C respectively. Take the convection heat transfer coefficient to be 6.5
W/m2/K and that the surrounding wall of the room is at a temperature of 20 oC.
Select one:
A 123.7 W
B. 86.4 W
C. 151.7 W
D. 100.5 W
E 43.0 W
Chapter 1 Solutions
Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)
Ch. 1 - 1.1 On a cold winter day, the outer surface of a...Ch. 1 - 1.2 The weight of the insulation in a spacecraft...Ch. 1 - 1.3 A furnace wall is to be constructed of brick...Ch. 1 - 1.4 To measure thermal conductivity, two similar...Ch. 1 - To determine the thermal conductivity of a...Ch. 1 - A square silicon chip 7mm7mm in size and 0.5-mm...Ch. 1 - A cooling system is to be designed for a food...Ch. 1 - 1.80 Describe and compare the modes of heat loss...Ch. 1 - Heat is transferred at a rate of 0.1 kW through...Ch. 1 - 1.10 A heat flux meter at the outer (cold) wall of...
Ch. 1 - 1.11 Calculate the heat loss through a glass...Ch. 1 - 1.12 A wall with a thickness is made of a...Ch. 1 - 1.13 If the outer air temperature in Problem is...Ch. 1 - Using Table 1.4 as a guide, prepare a similar...Ch. 1 - 1.15 A thermocouple (0.8-mm-diameter wire) used to...Ch. 1 - Water at a temperature of 77C is to be evaporated...Ch. 1 - The heat transfer rate from hot air by convection...Ch. 1 - The heat transfer coefficient for a gas flowing...Ch. 1 - 1.19 A cryogenic fluid is stored in a...Ch. 1 - A high-speed computer is located in a...Ch. 1 - 1.21 In an experimental set up in a laboratory, a...Ch. 1 - 1.22 In order to prevent frostbite to skiers on...Ch. 1 - Using the information in Problem 1.22, estimate...Ch. 1 - Two large parallel plates with surface conditions...Ch. 1 - 1.25 A spherical vessel, 0.3 m in diameter, is...Ch. 1 - 1.26 Repeat Problem 1.25 but assume that the...Ch. 1 - Determine the rate of radiant heat emission in...Ch. 1 - 1.28 The sun has a radius of and approximates a...Ch. 1 - 1.29 A spherical interplanetary probe with a 30-cm...Ch. 1 - A spherical communications satellite, 2 m in...Ch. 1 - A long wire 0.7 mm in diameter with an emissivity...Ch. 1 - Wearing layers of clothing in cold weather is...Ch. 1 - A section of a composite wall with the dimensions...Ch. 1 - A section of a composite wall with the dimensions...Ch. 1 - Repeat Problem 1.35 but assume that instead of...Ch. 1 - 1.37 Mild steel nails were driven through a solid...Ch. 1 - Prob. 1.38PCh. 1 - 1.39 On a cold winter day, the outside wall of a...Ch. 1 - As a designer working for a major electric...Ch. 1 - 1.41 A heat exchanger wall consists of a copper...Ch. 1 - 1.43 A simple solar heater consists of a flat...Ch. 1 - A composite refrigerator wall is composed of 5 cm...Ch. 1 - An electronic device that internally generates 600...Ch. 1 - 1.47 A flat roof is modeled as a flat plate...Ch. 1 - A horizontal, 3-mm-thick flat-copper plate, 1-m...Ch. 1 - 1.49 A small oven with a surface area of is...Ch. 1 - A steam pipe 200 mm in diameter passes through a...Ch. 1 - 1.51 The inner wall of a rocket motor combustion...Ch. 1 - 1.52 A flat roof of a house absorbs a solar...Ch. 1 - Determine the power requirement of a soldering...Ch. 1 - 1.54 The soldering iron tip in Problem 1.53...Ch. 1 - Prob. 1.55PCh. 1 - A pipe carrying superheated steam in a basement at...Ch. 1 - Draw the thermal circuit for heat transfer through...Ch. 1 - 1.60 Two electric resistance heaters with a 20 cm...Ch. 1 - 1.63 Liquid oxygen (LOX) for the space shuttle is...Ch. 1 - The interior wall of a large, commercial walk-in...Ch. 1 - 1.67 In beauty salons and in homes, a ubiquitous...Ch. 1 - The heat transfer coefficient between a surface...Ch. 1 - The thermal conductivity of fibreglass insulation...Ch. 1 - 1.71 The thermal conductivity of silver at 212°F...Ch. 1 - 1.72 An ice chest (see sketch) is to constructed...Ch. 1 - Estimate the R-values for a 5-cm-thick fiberglass...Ch. 1 - A manufacturer in the United States wants to sell...Ch. 1 - Referring to Problem 1.74, how many kilograms of...Ch. 1 - 1.76 Explain a fundamental characteristic that...Ch. 1 - 1.77 Explain each in your own words. (a) What is...Ch. 1 - What are the important modes of heat transfer for...Ch. 1 - 1.79 Consider the cooling of (a) a personal...Ch. 1 - Describe and compare the modes of heat loss...Ch. 1 - A person wearing a heavy parka is standing in a...Ch. 1 - Discuss the modes of heat transfer that determine...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Exhaust gases from a manufacturing plant are being discharged through a 10-m tall exhaust stack with outer diameter of 1 m wall thickness of 0.2 m, and thermal conductivity of 40 W/m-K. The exhaust gases are discharged at a rate of 1.2 kg/s while temperature drop between inlet and exit of the exhaust stack is 30°C, and the constant pressure specific heat of the exhaust gases is 1600 J/kg-K. On a particular day, the outer surface of the exhaust stack experiences radiation with the surrounding at 27°C, and convection with the ambient air at 27°C also, with an average convection heat transfer coefficient of 8 W/m2K. Solar radiation is incident on the exhaust stack outer surface at a rate of 150 W/m2, and both the emissivity and solar absorptivity of the outer surface are 0.9. Exhaust stack wall A-40 W/mK And m Exhaust gases Exhaust stack a, -8=0.9 Air, 27°C A-8 W/m²K T-T-30°C K Manufacturing plant Determine the inner surface temperature of the exhaust stack (up to 1 decimal place). The…arrow_forwardThe top of a large industrial hot water heater has been left uninsulated. The top may be modeled as a horizontal flat plate with a diameter of 1.30 meters. The outside temperature of the top of the hot water heater is 54.0°C. The air temperature (P = 1.00 atm) and the surrounding temperature of the room are 20.0°C. Calculate the heat transfer rate from the top of this hot water heater; including the effect of radiation (assume the emissivity of the top of the hot water heater is 0.37).arrow_forwardAn electric resistance space heater is designed such that it resembles a rectangular box 50 cm high, 80 cm long, and 15 cm wide filled with 45 kg of oil. The heater is to be placed against a wall, and thus heat transfer from its back surface is negligible. The surface temperature of the heater is not to exceed 75°C in a room at 25°C for safety considerations. Disregarding heat transfer from the bottom and top surfaces of the heater in anticipation that the top surface will be used as a shelf, determine the power rating of the heater in W. Take the emissivity of the outer surface of the heater to be 0.8 and the average temperature of the ceiling and wall surfaces to be the same as the room air temperature. Also, determine how long it will take for the heater to reach steady operation when it is first turned on (i.e., for the oil temperature to rise from 25°C to 75°C). State your assumptions in the calculations.arrow_forward
- Consider a person standing in a room at 18°C. Determine the total rate of heat transfer from this person if the exposed surface area and the skin temperature of the person are 1.7 m2 and 32°C. respectively, and the convection heat transfer coefficient is 5 W/m2-K. Take the emissivity of the skin and the clothes to be 0.9, and assume the temperature of the inner surfaces of the room to be the same as the air temperature.arrow_forwardAn uninsulated 100-mm diameter steam pipe runs for 25-meters inside a room whose walls and air are at a temperature of 25°C. The superheated steam inside the pipe maintains the temperature at the pipe surface at 150°C. If the natural convection heat transfer coefficient of the air outside the pipe is 10- m2-K and the surface emissivity is 0.8, compute for the total rate of heat transfer from the surface of the pipe in kW.arrow_forwardA 5.1-m internal diameter spherical tank made of 1.6-cm-thick stainless steel (k = 15 w/m- c) is used to store iced water at 0 C. the wall of the room are also at 31 C. The convection heat transfer coefficient at the inner and the outer surface of the tank are 80 w/m - c, respectively. Determine (a) the rate of heat transfer of the iced water and (b) the amount of iced at 0 C that melts during a 24 h period. the heat of fusion of water at atmospheric pressure is 333.7 kj/kg.arrow_forward
- A solid plate, with a thickness of 15 cm and a thermal conductivity of 80 W/m-K, is being cooled at the upper surface by air. The air temperature is 10°C, while the temperatures at the upper and lower surfaces of the plate are 50 and 60°C, respectively. Determine the convection heat transfer coefficient of air at the upper surface and discuss whether the value is reasonable or not for force convection of air. Air, T. = 10°C T1 = 50°C T2 = 60°C L = 15 cmarrow_forwardA furnace wall is made of 20 cm of magnesite brick and 20 cm of common brick. The magnesite brick is exposed to hot gases at 1200°C and common brick outer surface is exposed to 35°C room air. The surface heat transfer coefficient of the inside wall is 40 W/m²K and that of the outer wall is 20 W/m²K respectively. Thermal conductivities of magnesite and common brick are 4 and 0.5 W/mK respectively. Determine: i. Heat loss per m² of area of the furnace wall and ii. Maximum temperature to which common brick is subjectedarrow_forwardThere are 3 people in a hemispherical house with an inner radius of 1.8 m, designed for short-term shelter. The walls of the house are made of 50 cm thick material with a heat transfer coefficient of 0.15 W / mK. The heat transfer coefficient of this house is 6 W / m2K on the inner surface and 15 W / m2K on the outer surface. The temperature of the floor where the house is located is considered to be constant at -5 ° C. Each person in the house generates 105 W of body heat. When the indoor air temperature of the house is measured as -3 ° C, calculate the outside temperature.arrow_forward
- A 50-meter-long cast iron pipe with a 10-centimeter outside diameter goes through a 288 K temperature open environment. The temperature of the pipe's outer surface is 423 K, and the combined heat transfer coefficient on the pipe's outside surface is 25 W/m2 K. Considering and stating the necessary assumptions determine,(a) The rate of heat loss from the pipe (b) The energy lost per year if the cost of the fuel is 0.52 $/therm ( 1 therm = 105,500 kJ) c) The thickness of the insulation if 98% of the energy loss is planned to be saved. Consider the conduction coefficient of the insulation is 0.035 W/mK.arrow_forwardA pipe 30 m long with an outer diameter of 75 mm is used to deliver steam at a rate of 1500 kg / hour. The steam pressure is 198.53 kPa entering the pipe with a quality of 98%. The pipe that needs to be insulated with a thermal conductivity of 0.2 W / (m K) so that the quality of the steam only decreases slightly to 95%. The temperature of the outer surface of the insulation is assumed to be 25 ° C. The conductive of the pipe material and the situation of no pressure drop in the pipe. A. Determine the enthalpy of incoming vapor = Answer kJ / kg. b. Determine the enthalpy of steam that comes out = Answer kJ / kg. c. Determine the change / loss of steam heat along the flow = Answer watt. d. Determine the minimum required insulation thickness = Answer cm.arrow_forwardThe inside surface of an insulation layer is maintained at 350°C and the outside surface dissipates heat by convection and radiation to air and wall, respectively. The temperatures of air and wall are 15 °C. The insulation layer has a thickness of 10 cm and a thermal conductivity of 15 W/m.K. What is the value of the heat transfer coefficient at the outside surface of the layer, if the temperature at the outside surface should not exceed 225 °C? (The emissivity and the width of the surface are 0.3 and1 m., respectively. o-5.67x10-8 W/m²K*). Tw=15°. T=225°C ɛ=0.3 ТЬ3350°C To=15°C h.=? 10 cmarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license