When a slug of tracer is injected into a cascade of CFSTRs, amaximum value of C₁ occurs at t> 0 for all reactors except the first.Determine the time when the peak occurs in the nth reactor in termsof OH.

In a cascade of continuously stirred tank reactors (CSTRs), a slug of tracer injected at the inlet…

When a slug of tracer is injected into a cascade of CFSTRS, a maximum value of Cr occurs at t> 0 for all reactors except the first. Determine the time when the peak occurs in the nth reactor in terms of 0.

When a slug of tracer is injected into a cascade of CFSTRS, a maximum value of Cr occurs at t> 0 for all reactors except the first. Determine the time when the peak occurs in the nth reactor in terms of 0.

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter10: Oxidation, Degradation, Corrosion, Electroprocessing, Batteries, And Fuel Cells

Section: Chapter Questions

Problem 10.3P

See similar textbooks

Similar questions

(round off to 2 decimal places) is CIC, =0.8, the value of LCMFR/ LR 2 Consider the reactor shown in the figure. of a compound in the influent and The flow rate through the reactor is Q m'/h. The concentrations (in mg/L) effluent are C, and C, respectively. The compound is degraded in the reactor following the first order reaction. The mixing condition of the reactor can be varied such that the reactor becomes either a completely mixed flow reactor (CMFR) or a plug-flow reactor (PFR). The length of the reactor can be adjusted in these two mixing conditions to LCMFR and LPER while keeping the cross- section of the reactor constant. Assuming steady and for state %3D Q, C.
(a) Prove that for a first order decay reaction (k1= 2 days-1) taking place in reactors of identical size at steady state, it does not matter if you use a CMFR followed by a PFR or a PFR followed by a CMFR (i.e. show that the final treated effluent concentration, in mg/L, is approx. the same in each scenario). Assume the volume of each reactor is 15 L and the reactors in series will be used to treat a wastewater containing 5 mg/L of contaminant “C” at a flowrate of 10 L/day. (b) Does this remain true if a second order decay reaction was taking place? If not, which sequence of reactors is more efficient (i.e. removes more of the contaminant)? Assume the same reactor volumes, flow rate and contaminant concentration as in part (a), and k2 = 2 Lmg-1day-1 . You must show your derivation of the expression for a PFR with 2nd order decay.
When the system is at equilibrium at a particular temperature, C(s) + CO2(g) =2 CO(g) a 4-L flask contains 0.40 mol CO, 0.80 mol CO2, and 0.45 mol C. What is the value of K, at that temperature? O 0.050 O 0.20 1.8 O 0.44
A second-order irreversible elementary reaction 2A -> product is carried out in a batch reactor. It was found that it took 30 min for a reaction to reach 90% conversion. What would be the time required to reach the same degree of conversion if (a) the initial concentration of A was doubled, (b) the reaction rate constant was doubled, and (c) the reactor volume was doubled.
Consider the reactor shown in the figure. The flow rate through the reactor is Q m/h. The concentrations (in mg/L) of a compound in the influent and effluent are C, and C, respectively. The compound is degraded in the reactor following the first order reaction. The mixing condition of the reactor can be varied such that the reactor becomes either a completely mixed flow reactor (CMFR) or a plug-flow reactor (PFR). The length of the reactor can be adjusted in these two mixing conditions to LCMFR and LPER while keeping the cross-section of the reactor constant. Assuming steady state and for C/C, = 0.8, the value of LoMER/LPER (round off to 2 decimal places) is_ Q, C Co
(iii) If HOCI (hypochlorous acid) degrades in water per first-order kinetics with a rate constant of 0.12/d. the initial concentration of HOCI is 12 mg/L (a) How long does it take to be reduced to 0.8 mg/l ? (b) what would be concentration after 4 hours? (6)
3. A CFSTR receives a flow rate of 100 m³/sec. There is one influent stream coming into the reactor and one effluent stream leaving the reactor. The concentration of a chemical in the influent stream is reduced by 95% in the reactor. Given, the chemical has a first order decay rate of 0.15/d. Find the volume of the CFSTR (in m³).
In the previous question a trisodium phosphate solution was prepared. Since the molecular weight of Na3PO4 is 163.94, what concentration in moles per liter was made by combining 0.328 g Na3PO4 with 1.00 L water? Your answer should be in the form 0.---
Water with 90 mg/L of a degradable contaminant flows through a reactor. The influent flow rate entering the reactor is 100 m3/day. The reactor has a volume of 200 m3. The contaminant is degraded in the reactor following first-order reaction kinetics with a rate constant of 1.0 d-1. The reactor is well mixed throughout the time (i.e., a CSTR). Whatis the contaminant concentration in the reactor when reaching a steady state condition?(_________)
A nuclear fuel pellet consists of an aluminum cladding[E1 = 90 GPa; α1 = 42.2 × 10-6 /°K] with an outsidediameter of D and an inside diameter of d, restrained toa uranium core [E2 = 190 GPa; α2 = 15.9 × 10-6 /°K] witha diameter d. [D = 17 mm; d = 14 mm; L = 13 mm]Determine the normal force in the aluminum cladding ifthe temperature of the pellet is raised by ΔT = 317 °K.[Hint: The total axial deformations in both materials areidentical. The axial forces induced in both aluminum anduranium are also identical with opposite signs.]
(i) For a waste water, the BOD, at 20°C is found to be 200 mg/l. What will be BOD, at 30°C for the same? The reaction constant 'K' (to the base e) at 20°C is 0.2 per day.
Please help me with this conversion factors with lables on it. Please show me the work.