A thin cylindrical steel pressure vessel of diameter 6 cm and wall thickness 3 mm is subjected to an internal fluid pressure of intensity 'p'. If the ultimate strength of steel 3600 kg/cm², the bursting pressure will be

A thin cylindrical steel pressure vessel of diameter 6 cm and wall thickness 3 mm is subjected to an internal fluid pressure of intensity 'p'. If the ultimate strength of steel 3600 kg/cm², the bursting pressure will be

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A steel rod, 100 mm long is held between two rigid supports. It is heated by 20°C. If the…

A: Given data- Length of the steel rod L=100 mmrod is between rigid supportstemperature difference…

Q: A metal bar of length 100mm is inserted between two rigid supports and its temperature is increased…

A: Given data- Length of the bar L=100 mmIncrease in temperature∆T=10oCCoefficient of thermal expansion…

Q: A 2.5 m cubic reservoir was designed to store oil, whose density is 900 kg/m³, 1.5 m high under…

Q: Two semi-spherical thin-walled vessels are joined together by attaching 40-mm bolts around the…

Q: A cylindrical boiler with an outside diameter of 3.60 m and a wall thickness of 40 mm is made of a…

Q: Determine the determinacy and stability of the figure shown.

Q: II. From the figure shown the coefficient of friction are as follows: 0.23 at the floor, 0.28 at the…

Q: The material of a rubber balloon has a Poisson's ratio of 0.5. If uniform pressure is applied to…

A: Given Data; Poisson's Ratio = (μ) = 0.5 Uniform pressure applied to blow to balloon. To Determine…

Q: A metal bar of length 100mm is inserted between two rigid supports and its temperature is increased…

Q: THIN WALLED PRESSURE VESSELS SITUATION: A cylindrical water tank is 8 m in diameter and 12 m long.…

A: Given:- Diameter of cylinder = 8 m Length of cylinder = 12 m Material stress = 40 MPa

Q: A thin cylindrical shell made of mild steel plate is 1000 mm in diameter. It is to be subjected to…

Q: The strength per meter of the longitudinal joint of a cylindrical tank is 475 kN, whereas the girth…

Q: A pressure of 65 MPa at a specific depth in the ocean and the average bulk modulus of elasticity is…

Q: Which of the following is/are true about thin walled pressure vessels? A vessel can be classified as…

Q: In a rotating cylinder test, the inner cylinder is of diameter 0.2 m and the outer cylinder of…

A: Given: Diameter of inner cylinder, D1 = 0.2 m Radius of inner cylinder, R1 = 0.2/2 = 0.1 m Diameter…

Q: W C hz В D D D hi E E L System 1 System 2 System 3

A: The given data is: w= 50 kN/m h1 = 4 m h2 = 2 m L =12 m System 1 = Fixed arch System 2 = Two hinged…

Q: The thin steel cylinder just fits over the inner aluminum cylinder as shown in Fig. 4-7. Find the…

A: Given: Rise in temperatureT=33° C Est=200 GPaEal=72 GPaαst=17.3×10-6/°Cαal=22.5×10-6/°C

Q: The pressure inside a soap bubble of 50 mm diameter is 25 N/m? above atmospheric pressure. The…

Q: A metal bar of length 100 mm is inserted between two rigid supports and its temperature is increased…

A: A metal bar between two rigid supports with the below data is given-To Find-The value of the stress…

Q: A 0.35-m long steel rod with a round cross-section (25 mm) is resting on a frictionless surface. The…

A: The given data is: Length of steel rod (L) = 0.35 m Diameter of steel rod (d) = 25 mm Coefficient of…

Q: Calculate DOl and identify the following structure as determinate,

A: DOI HAS TO CALCULATE OF THE FRAME GIVEN

Q: Determine the reaction at A in the given figure. (please submit your solution for this item)

A: Solve for reaction:W1=12×20.3W2=20.6W3=12×20.45

Concept explainers

Storm Sewers and Detention

The storm drains system transports rainwater or stormwater and other runoff from roads, parking lots, and roof downpipes directly to nearby creeks, rivers, or the sea without any treatment.

Question

A thin cylindrical steel pressure vessel of diameter
6 cm and wall thickness 3 mm is subjected to an
internal fluid pressure of intensity 'p'. If the ultimate
strength of steel 3600 kg/cm2, the bursting
pressure will be

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

2. A 2-m long aluminum pipe at 27°C is heated until it is 2.0024 m at 77°C. What is the coefficient of linear expansion of aluminum? Complete FBD, FORMULA, AND SOLUTION
The minimum safe bending radius of a certain polyethylene tube is theoutside diameter times 31⁄2. The tube has an outside diameter of 3⁄8 inch.What is the minimum bending radius?
A cast-iron cannonball is found by a diver on the bottom of a harbor (SG of harbor water = 1.02) . The cannonball has a volume of 0.1 ft3 . The cast-iron has a specific gravity of 7.40. What force (F) is necessary to lift the cannonball off the bottom (find F in lb)? (use specific weight of water = 62.4 lb/ft3 )
Glycerin flows at 35 m through a 150 mm diameter new wrought iron pipe at a velocity of 3 m/s. It has an absoluteviscosity of 1.50 Pa-s and a specific gravity of glycerin = 1.26.3. Solve for the coefficient of pipe friction
14
A steel penstock 60 cm in diameter has a shell thickness of 1.2 cm. The modulus of elasticity of pipe shell material is 2.1 × 105 N/mm² with a Poisson's ratio of 1/4, and the volume modulus of elasticity of water is 2.1 × 103 N/mm². The pipe is designed to discharge water at mean velocity of 2.1 m/sec Determine the water hammer pressure rise caused by sudden closure of the valve at the d/s end (1) neglecting the elasticity of the pipe material; and (2) considering the elasticity of the pipe material.
P14.2 A spherical gas-storage tank with an inside diameter of 6.5 m is being constructed to store gas under an internal pressure of 1.25 MPa. The tank will be constructed from steel that has a yield strength of 420 MPa. If a factor of safety of 3.0 with respect to the yield strength is required, determine the minimum wall thickness required for the spherical tank.
A cylindrical specimen of a metal alloy 47.5 mm long and 9.72 mm in diameter is stressed in tension. A true stress of 397 MPa causes the specimen to plastically elongate to a length of 54.3 mm. If it is known that the strain-hardening exponent for this alloy is 0.2, calculate the true stress (in MPa) necessary to plastically elongate a specimen of this same material from a length of 47.5 mm to a length of 55.8 mm. i MPa
A solid cube of side 1 m is kept at a room temperature of 32°C. The coefficient of linear therma expansion of the cube material is 1 x 105/°C and the bulk modulus is 200 GPa. If the cube is constrained all around and heated uniformly to 42°C, then the magnitude of volumetric (mean) stress (in MPa) induced due to heating is و او را
Two semi-spherical thin-walled vessels are joined together by attaching 30-mm bolts around the circumference to form a spherical vessel which can carry a pressure of 3 MPa. If the internal diameter of the vessel is 2 m and the allowable stress in the bolts is 40 MPa, how many bolts must be used ? (answer in whole number) Round your answer to 0 decimal places.
A cylindrical pressure vessel is fabricated from steel plates which have a thickness of 20 mm. Thediameter of a pressure vessel is 500 mm and its length is 3.0 m. Determine the maximuminternal pressure which can be applied if the stress in the steel is limited to 140 MPa. If the theinternal pressure were increased until the vessel burst, sketch the type of fracture which wouldoccur. Write in a paper with complete solution