2. At temperature of 20C, the BOD, was determined to be 180 mg/L 0₂. At 20 C, the reaction rate (constant) is k₂0 = 0.2 d.¹ Find the following: a. BOD ult b. Reaction rate k₁, (at temperature of 15C c. BOD, at temperature of 15C

2. At temperature of 20C, the BOD, was determined to be 180 mg/L 0₂. At 20 C, the reaction rate (constant) is k₂0 = 0.2 d.¹ Find the following: a. BOD ult b. Reaction rate k₁, (at temperature of 15C c. BOD, at temperature of 15C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The assembly consists of a brass shell (1) fully bonded to a solid ceramic core (2). The brass shell [E = 115 GPa, a = 18.7 × 10-6/°C] has dout 50mm. and din = 35mm. The ceramic core [E = 290 GPa, α = 3.1 x 10-6/°C] has a diameter dout = 35mm. At a temperature of 15°C, the assembly is unstressed. AT = 60°C. Find the internal stress in the brass. = 200 mm Brass shell (1) (2) Ceramic core
Which of the following alloys would form a complete substitutional solid solution? Metal 1 is BCC, metal 2 is FCC, and atomic radíus difference is 12%. Metal 1 is FCC, metal 2 is FCC, and atomic radius difference is 12%. Metal 1 is FCC, metal 2 is FCC, and atomic radíus difference is 15%. Metal 1 is HCP, metal 2 is FCC, and atomic radius differene is less than 15%. Metal 1 is BCC, metal 2 is BCC, and atomic radius difference is at least 15%.
A 1.0 meter long A36 steel rod with a diameter of 40mm is lightly attached at both end of the rod, end A and end B. A collar is located in the center of the rod. The initial temp is 60 degrees C. The final temperature is 35 degrees C. Determine the force that must be applied to the collar so that the reaction at B is zero.Given:Delta T=25 degrees CE for A36 steel: 200 GPaCoeff of thermal expansion: 12(10^-6)/degree C
An aluminum pipe has a length of 54 m at a temperature of 10°C. An adjacent steel pipe at the same temperature is 8 mm longer. At what temperature will the aluminum pipe be 24 mm longer than the steel pipe? Assume that the coefficient of thermal expansion for the aluminum is 22.5x10-6/°C and that the coefficient of thermal expansion for the steel is 12.5×10-6/°C.
A magnesium-lead alloy of mass 6.4 kg consists of a solid a phase that has a composition just slightly below the solubility limit at 300°C (570°F). The magnesium-lead phase diagram is shown in Animated Figure 9.20. (a) What mass of lead is in the alloy? i kg (b) If the alloy is heated to 400°C (750°F), how much more lead may be dissolved in the a phase without exceeding the solubility limit of this phase? kg
Figure P2.33 shows a portion of the H,O-NaCl phase diagram. 10 Liquid (brine) Salt Ice + -10 F liquid (brine) liquid (brine) -20 Ice + salt -30 NaCI 10 20 30 H2O 100 90 80 70 FIGURE P2.33 Composition, weight % a. Using the diagram, briefly explain how spreading salt on ice causes the ice to melt. Show numerical examples in your discussion. b. At a salt composition of 10%, what is the temperature at which ice will start melting? c. What is the eutectic temperature of the ice and salt combination? Temperature, °C
An aluminum pipe has a length of 69 m at a temperature of 8°C. An adjacent steel pipe at the same temperature is 5 mm longer. At what temperature will the aluminum pipe be 15 mm longer than the steel pipe? Assume that the coefficient of thermal expansion for the aluminum is 22.5×10-6/°C and that the coefficient of thermal expansion for the steel is 12.5×10-6/°C.
Problem # 1: The two rods as shown in the figure are attached to each other and the aluminum rod is fixed at the wall. The rods are initially unstressed and then a 20, 000 lb horizontal force is applied to the end of the brass rod as shown. Additionally, the rods experience a temperature increase of 80 °F. Use Linear coefficient of Expansion: Aluminum 13 x 10-6/°F Brass = 11 x 10-6/°F Young's Modulus: EAluminum = 10 x 106 lb/in2; EBrass = 15 x 106 lb/in² Determine; a) the final stress that develops in the aluminum rod, b) the total displacement of point C. Aluminum 10 ft B Aal- 2in² Brass 6 ft C 2 1in² Abr F = 20,000 lb
Which of the following is false regarding factor of safety in the design of structures? a. It considers uncertainties in the material properties. b. A higher factor of safety is preferable in designing safe structures c. It should not be less than 1 to ensure the structure’s safety. d. It considers changes in the loading pattern on the structure.
1. A bar with a constant cross section A is fixed at both ends. The bar is made of two different materials, that are joint together at point C. a) What are the reaction forces, if an external force F is applied at point C? b) Determine the normal force that is caused by a pure heating by AT. Given: Es Eat ast - 1 SAINT LC = 3, Steel Aluminiun
An aluminum-alloy rod has a length of 8.1814 cm at 14.00°C and a length of 8.1942 cm at the boiling point of water. (a) What is the length of the rod at the freezing point of water? (b) What is the temperature if the length of the rod is 8.1916 cm? prob (a) Number i Units (b) Number i Units