Answered: [14] Electrolysis process is based on :…

[14] Electrolysis process is based on : * thermal effect of current O chemical effect of current O luminous effect of current O magnetic effect of current

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: There are some sources in materials which result in electrical resistivity, some of those sources…

A: The correct answer is:a. All options

Q: The term BOD stands for: A) Biological Oxygen Demand B) Biochemical Oxygen Demand C) Biological…

A: Biochemical Oxygen Demand (BOD) is a key environmental indicator used to assess water quality.…

Q: 11-13 The Cu-Za phase diagram is shown in Figure 11-27. (a) Are any intermetallic compounds pres-…

A: Given:- Cu-Zn phase diagram To find:- a) stoichiometric or nonstoichiometric b)Solid solutions…

Q: The rate of corrosion in a galvanic cell can be reduced by: a. Increasing the temperature of the…

A: Reducing cathodic surface area compared to anodic surface area, leads to reduction in cathodic…

Q: In wastewater treatment plants, ammonium ion is removed from the water by raising the pH to form…

A: a) The equilibrium reaction that describes the process of ammonium conversion to ammonia is given as

Q: A 9.00-mol sample of H₂ gas is contained in the left side of the container shown below, which has…

Q: 21. To gain structural strength, the dimensions of aluminum are increased. T or F 22. 35% of…

A: Comment As per our policy, we cannot answer all multiple subparts, Since your question has multiple…

Q: It is seen that solids and liquids will have different coefficients of volume expansions for…

A: Coefficient of volume expansion:- The unit increase in the unit volume of any substance following…

Q: In term of stability and based on standard electrode potentials, which one of the following metals…

Q: Water contained in a closed, rigid tank, initially at 100 lbf/in², 800°F, is cooled to a final state…

Q: Question 90 of 96 How many moles of NH, form when 32.4 Lof H gas completely reacts at STP according…

A: At STP,

Q: What are the differences and similarities between metal catalysed and enzyme catalysed lipid…

A: The flow of fluid includes movement of an unbalanced fluid. As long as unequalled forces are in…

Question

[14] Electrolysis process is
based on : *
O thermal effect of current
O chemical effect of current
O luminous effect of current
magnetic effect of current

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A teapot with a surface area of 665 cm2 is to be plated with silver. It is attached to the negative electrode of an electrolytic cell containing silver nitrate (Ag+ NO3−). The cell is powered by a 12.0-V battery and has a resistance of 1.30 Ω. If the density of silver is 1.05 104 kg/m3, over what time interval does a 0.133-mm layer of silver build up on the teapot?
An aluminum pipe has a length of 75 m at a temperature of 18°C. An adjacent steel pipe at the same temperature is 0.005 m longer than the aluminum pipe. At what temperature (0C) will the aluminum pipe be 0.015 mm longer than the steel pipe? (Assume that the coefficients of thermal expansion of aluminum and steel are aa = 23 x 10–6/°C and as = 12 x 10–6/°C, respectively.)
(79 The correct electron-dot formula for magnesium fluoride is: O a -Mg-F: Next Page Back
26) Given the T-T-T curve below, select the process that will result in a microstructure of nearly all bainite. C. Cool to 400°C, hold for 20 seconds, then quench to room temperature Cool to 500°C, hold for 10 seconds, then quench to room temperature Quench to 125°C, hold for 10 seconds, then reheat to 600°C for more than 100 seconds d. Cool to 725°C, hold for 1,000 seconds, then quench to 125°C Cool to 600°C, hold for 1 second, the quench to room temperature f. none of the above 900 Temperature (°C) 800 A+C 700 A+P 600 500 A+B 400 A 300 200 M(start) M(50%) 100 M(90%) TT 1600 1400 1200 1000 800 600 50% 0 1 10 102 103 104 105 106 Time(s) 400 200 Temperature (°F) 27) Fatigue failure situations are typically dependent upon which combination of the following factors? Slip plane, slip direction, and orientation of the applied load b. Yield strength, elastic modulus, and ductility of the material c. Temperature, time, and applied stress d. Stress amplitude, frequency of loading, and number…
A magnesium-lead alloy of mass 6.4 kg consists of a solid a phase that has a composition just slightly below the solubility limit at 300°C (570°F). The magnesium-lead phase diagram is shown in Animated Figure 9.20. (a) What mass of lead is in the alloy? i kg (b) If the alloy is heated to 400°C (750°F), how much more lead may be dissolved in the a phase without exceeding the solubility limit of this phase? kg
26) Given the T-T-T curve below, select the process that will result in a microstructure of nearly all bainite. a. Cool to 400°C, hold for 20 seconds, then quench to room temperature b. Cool to 500°C, hold for 10 seconds, then quench to room temperature c. Quench to 125°C, hold for 10 seconds, then reheat to 600°C for more than 100 seconds d. Cool to 725°C, hold for 1,000 seconds, then quench to 125°C e. Cool to 600°C, hold for 1 second, the quench to room temperature Temperature (°C) f. none of the above 900 800 H A+C 1600 1400 700- 1200 A+P 600 P 1000 500H A+B 800 400- Temperature (°F) 4 A 300- M(start) 200 M(50%) 100- M(90%) 600 50% T 0 1 10 102 103 10 105 106 Time (s) 400 200 27) Fatigue failure situations are typically dependent upon which combination of the following factors? a. Slip plane, slip direction, and orientation of the applied load b. Yield strength, elastic modulus, and ductility of the material c. Temperature, time, and applied stress d. Stress amplitude, frequency of…
41)