A water has the following analysis (mg/L as ion or compound): Na+ 20 mg/L 40 mg/L K 30 mg/L 67 mg/L Ca²+ 15 mg/L 0 mg/L 20 mg/L 5 mg/L 2 mg/L 10 mg/L Mg2+ Sr²+ CI HCO3 2- CO3²- SO₂²- NO3 Atomic weight of Na = 23, K = 39.10, Ca = 40.08, Mg = 24.31, Sr= 87.62, Cl = 35.45, H = 1, C = 12, 0 = 16, S = 32.07, and N = 14) What is the total hardness in mg/L as CaCO3? What is the carbonate hardness in mg/L as CaCO3? A/ What is the noncarbonate hardness in mg/L as CaCO3? A

A water has the following analysis (mg/L as ion or compound): Na+ 20 mg/L 40 mg/L K 30 mg/L 67 mg/L Ca²+ 15 mg/L 0 mg/L 20 mg/L 5 mg/L 2 mg/L 10 mg/L Mg2+ Sr²+ CI HCO3 2- CO3²- SO₂²- NO3 Atomic weight of Na = 23, K = 39.10, Ca = 40.08, Mg = 24.31, Sr= 87.62, Cl = 35.45, H = 1, C = 12, 0 = 16, S = 32.07, and N = 14) What is the total hardness in mg/L as CaCO3? What is the carbonate hardness in mg/L as CaCO3? A/ What is the noncarbonate hardness in mg/L as CaCO3? A

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the amount of barium from Sodium sulphate in a liter. A 100 ml solution of sodium sulphate (Na2SO4) is treated with solution of Barium chloride(BaC12). The precipitate, then ignited and weighed. the precipitate(BaSO4) weight is 0.1 gm. Mol.Wt of BaSO4 233.42 gm/mol, At. Wt of barium= 56 gm/mol. %3D
26) Given the T-T-T curve below, select the process that will result in a microstructure of nearly all bainite. C. Cool to 400°C, hold for 20 seconds, then quench to room temperature Cool to 500°C, hold for 10 seconds, then quench to room temperature Quench to 125°C, hold for 10 seconds, then reheat to 600°C for more than 100 seconds d. Cool to 725°C, hold for 1,000 seconds, then quench to 125°C Cool to 600°C, hold for 1 second, the quench to room temperature f. none of the above 900 Temperature (°C) 800 A+C 700 A+P 600 500 A+B 400 A 300 200 M(start) M(50%) 100 M(90%) TT 1600 1400 1200 1000 800 600 50% 0 1 10 102 103 104 105 106 Time(s) 400 200 Temperature (°F) 27) Fatigue failure situations are typically dependent upon which combination of the following factors? Slip plane, slip direction, and orientation of the applied load b. Yield strength, elastic modulus, and ductility of the material c. Temperature, time, and applied stress d. Stress amplitude, frequency of loading, and number…
Considering an alloy of the two soluble components A and B described by a phase diagram similar to that shown in Figure 2.14, determine the masses of the alloy that are in the liquid and solid phases at a given temperature if the total mass of the alloy is 100 g, component B represents 45% of the alloy, 17% of the liquid is component B, and 65% of solid is component B.
Determine potential energv stored in ball m=3.3 kg h=7 m g=10 m/s2
A magnesium-lead alloy of mass 6.4 kg consists of a solid a phase that has a composition just slightly below the solubility limit at 300°C (570°F). The magnesium-lead phase diagram is shown in Animated Figure 9.20. (a) What mass of lead is in the alloy? i kg (b) If the alloy is heated to 400°C (750°F), how much more lead may be dissolved in the a phase without exceeding the solubility limit of this phase? kg
öalg äbäi is often described as the area of chemistry responsible for characterizing the composition of matter, both qualitatively (what is present) and quantitatively (how much is present). It was dealing with the identification and .determination of compounds
41)
Consider the equilibrium system described by the chemical reaction below. A 1.00 L reaction vessel was filled with 2.00 mol SO2 and 2.00 mol NO2 and allowed to react at a high temperature. At equilibrium, there were 1.30 mol of NO in the vessel. Determine the concentrations of all reactants and products at equilibrium and then calculate the value of Kc for this reaction. SO:(g) + NO2(g)= SO:(g) + NO(g) 1 2 NEXT Based on the given values, fill in the ICE table to determine concentrations of all reactants and products. SO:(g) NO:(g) SO:(g) NO(g) + + Initial (M) Change (M) Equilibrium (M) RESET +x -X 1.00 2.00 1.30 -1.00 -1.30 2.30 2.70 0.70 1.35 2.00 - x 2.00 + x Activa Go to Se 1L
An aluminum-alloy rod has a length of 8.1814 cm at 14.00°C and a length of 8.1942 cm at the boiling point of water. (a) What is the length of the rod at the freezing point of water? (b) What is the temperature if the length of the rod is 8.1916 cm? prob (a) Number i Units (b) Number i Units