three plates are attached using two 3/4-inch bolts, as shown in Fig. P2.31. Determine the shear stress in each bolt due to a force P = 12klb. Tres placas se unen por medio de dos pernos de % plg, como se indicaen la Fig. P2.31. Determinar el esfuerzo cortante en cada perno debido a unafuerza P = 12 klb.2,31FIGURA P2.31

Answered: Image /qna-images/answer/235fd24b-da7e-4dd5-8814-9e14e86b8342.jpg

Answered: three plates are attached using two…

three plates are attached using two 3/4-inch bolts, as shown in Fig. P2.31. Determine the shear stress in each bolt due to a force P = 12klb.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 1. The figure shows a roof truss and the detail of the connection at joint D. Member DE is angle…

Q: ACTIVITY The figure shows a roof truss and the detail of the connection at joint B. Members BC and…

Q: the glued splice is 75 psi, determine (a) the largest load P that can be safely supported, (b) the…

A: θ=90-60=30°We knowσθ=PAcos2θ75=P5×3cos230P=1500lbs=1.5kips

Q: A bolted lap joint is used to connect a rectangular bar to a hanger bracket, as shown in Fig.…

A: Given data, Allowable shear stress in bolt = 80MPa Diameter of bolt shank = 15 mm To find out the…

Q: Determine the structure if it is determinate or indeterminate and if indeterminate. What is the…

A: Ds=R-3- €(n-1) where R=external support reaction n=number of members meeting at internal pin

Q: The Load P = 2600 lb is applied on a five bolt truss. If the average shear stress in the bolts must…

A: Given: The 5 bolts structure,The load given is 2600 lb,The total number of bolts is 5,The average…

Q: Q1: For the simply supported beam of the cross sectional dimensions and load shown in the figure,…

Q: = AT beam supports the three concentrated loads shown in Fig. P-556. N.A. is 3.5 in., INA- 97.0 inf.…

A: Given: P=1600 lbsy=3.5 inINA=97 in4

Q: In the steel structure shown a 6 mm diameter pin is used at C and 10 mm diameter pin is used at B.…

A: Given:Diameter of pin at C is 6mmDiameter of pin at B is 10 mmRequired:Largest P applied

Q: A PROB. 1.8-12 a 2P B (a) D XII Gusset plate Rivet (b) Section

Q: The following image shows a front and side view of the column connection. The bolts have a diameter…

Q: PART 2 : COMPUTE THE AXIAL STRESSES IN ALL MEMBERS OF THE TRUSS SHOWN. USE 300 sq. mm AND 250 sq. mm…

A: Question is based on truss supported on roller and hinged support. Span length of member and loading…

Q: 2.31. The curved rigid bar ADB is joined to the two elastic bars OA and OB as shown in Fig. 2-48.…

A: The solution is given below.Explanation:Approach to solving the question: Detailed explanation:…

Q: 60 KN A BLOCK SHOWN IS SUBJECTED TO A TRIAXIAL LOADING OF THREE 40 mm UNIFORMLY DISTRIBUTED FORCES.…

A: As per guidelines we need to answer only 1st 3 subparts of the question.

Q: Part 1 Rigid bar ABC is supported by bronze rod (1) and aluminum rod (2), as shown. A concentrated…

Q: Problem 3: Six 7/8-in-diameter rivets fasten the plate to the fixed member. Determine the average…

Q: 1) Use the notion of symmetry and construct an FBD for only the upper half of the left-hand wood…

A: Solution; Given that; β=74° P=1360 b=1.55 in. d=3.70⇒d/2=1.85 length of AB=1.85sinβ2LAB=…

Q: 7.5 mm SN kN SN kN 12 mm 12 mm 7.5 mm 12.5 mm SN kN SN_kN 18 mm 25 mm 18 mm

A: determine the following: Maximum bearing stress at joints ( bolts and plates). Shearing stress If…

Q: The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are…

A: Given data: Shear stress τ = 70 MPa Bearing stress σ = 140 MPa Diameter of rivet d = 19 mm For the…

Q: QI: Find the normal stresses at sections A-A, B-B, C-C, and, D-D for the body as shown in figure…

A: As per guidelines we are supposed to answer only first question

Q: Six rivets are used in the connection shown in the figure. If both P=50kN, what is the minimum…

Q: 4.Calculate and determine the nature of the forces in the bar EF,FC ,and BC with ritter cut method

A: Hint: Height of F = 3 tan30°=1.73 m φ=tan-11.731=59.97° ∑MA=0-RD×6 + 30×4 +…

Q: Prob. 2.9-8. The steel eyebar in Fig. P2.9-8 has cross-sec- tional dimensions 25 mm x 100 mm. To…

Q: med joint by the g. Determine t

A: Dimension of block = 2.5in.*2.5in. Sliding angle = 55° Length of steel key = 2.5in. Working Bearing…

Q: .Determine the cracking moments for the section shown if f = 4000psi. C 30"- 4" 17" 24" 1 #11 3" 6"

Q: A W18x40 standard steel shape is used to support the loads shown on the beam. Assume P= 26 kips, w =…

Q: Figure P-130 shows a roof truss and the detail of the riveted connection at joint B. Using allowable…

Q: The steel shafts are connected together using a fillet weld as shown in the figure below. (Figure 1)…

A: T = 63 N. m

Q: 8 kips 4 kips 4 kips d, =2" 15 kips 15 kips -d2 =1.5" !0 kips 20 kips d, =3" A Fig. for Problem #2

A: There are 3 bars AB, BC, CDThe forces on those bars are also given.Diameter of bar CD, d1 = 2…

Q: 1.51 In the steel structure shown, a 6-mm-diameter pin is used at C and 10-mm-diameter pins are used…

Q: Three plates are welded together to form the section shown. Dimensions of the cross section are b=…

Q: The figure shows a roof truss and the detail of the connection at joint D. Member DE is angle…

Q: D 30 kN 70 kN 2 m 12 mm-thick gusset plate 10 -mm-thick 2 m angle 1.5 m-15 m- 15 m--15 m 8 mm-thick…

Q: 1. Determine bar forces in the truss beldw 30 KN 30 KN 30 N 2m

Q: Compute the deformation and member force of the truss member shown in Figure 1 under the given…

Q: Cm 4m 4m Gom G Gm. F Gm 76 KN 14 76 KN

Q: By inspection, determine the zero-force members in each truss. Identify the zero-force member by…

A: As per our guidelines we are suppos d to answer first three subparts. Kindly repost other part as…

Q: A roof truss and the detail of the connection at joint B are shown in the figure. Angle sections…

A: For the given roof truss:

Q: Five plates with thickness t are bolted together by a bolt with diameter d. Which of the following…

Q: A short prismatic member is subjected to load P- 100 kips at comer shown by Red Dot as shown in…

A: Given: Load, P= 100 kips A1=3×12=36''y1=122=6''A2=3×12=36''y2=122=6''A3=9×3=27''y3=32=1.5''

Q: The allowable unit stress in shear on a fillet weld is 13,600 psi, and the total actual length of…

A: Given data: P=9600 lb Permissible shear stress, PSS=13600 psi Length of weld, L=3 in. Weld size=?

Q: 1. Given the connection shown below carrying a load P = The connection consists of four pieces 20mm…

Concept explainers

Connections

In steel structures, connections are the members that join two or more steel members. The connections are the most important members of any steel structure, and hence, they are designed more carefully. The majority of the construction cost of steel structures is incurred due to the connections. The design of connections is done as per the recommendations and specifications of the American Institute of Steel Construction (AISC).

Question

three plates are attached using two 3/4-inch bolts, as shown in Fig. P2.31. Determine the shear stress in each bolt due to a force P = 12klb.

Tres placas se unen por medio de dos pernos de % plg, como se indica
en la Fig. P2.31. Determinar el esfuerzo cortante en cada perno debido a una
fuerza P = 12 klb.
2,31
FIGURA P2.31

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Please help me. I'll give a thumbs up
1. Refer to the sketch below. a. What type of joint is shown? b. What type of weld is shown? C. Is the weld in shear or normal stress? d. Calculate the magnitude of stress in the weld. K /P= 50 Kip /P = 50 Kip 10" I 1/4"
6 5:03 M docs.google.com/draw 10 Finals 4 Saved to Drive File Edit View Tools Help Last edit was made yesterday at 11:49 PM by Noel Amatong View only. Bronze The compound shaft shown in Fig. P-324 is attached to rigid supports. For the bronze segment AB, the maximum shearing stress is limited to 8000 psi and for the steel segment BC, it is limited to 12 ksi. Determine the diameters of each segment so that. each material will be simultaneously stressed to its permissible limit when a torque T 12 kip-ft is applied For bronze, G = 6 x 106 psi and for steel, G = 12 x 106 psi. 6 ft 6 ** ** ...| ...| 29%- B 4 ft [20 Share • Ⓒ e ?
Pin diameter = 10 mm Gusset plate 15 kN Pin 50 mm Steel plate 6 mm thickness Column For the pin connection shown, determine the normal stress acting on the gross area, the normal stress acting on the net area, the shear stress in the pin, and the bearing stress in the steel plate at the pin.
Question-02Describe the various types of stresses developed in the shaft AB due to load P acting at the end C as shownin Figure 1.
The strain at point A on the bracket has components €g = 330 (10-6), e, = 560 (10-6), Yxy = -570 (10-6), e; = 0. Correct Part B Determine the maximum shear strain in the x - y plane. = 6.15x10-4 'in-plane Submit Previous Answers Correct Part C Determine the absolute maximum shear strain. (Figure 1) Figure < 1 of 1 vec -4 Yaa = 7.99 • 10 max Submit Previous Answers Request Answer X Incorrect; Try Again
6
Number of half joints (J2)?
This question was answered but all parts are showing. So, I need a question credited back to me!
Please help me with my homework and use ASEP STEEL HANDBOOK 2004 volume 1 Dimensions and Properties Third Edition, to find the AISC. PLEASE SHOW COMPLETE SOLUTIONS AND DETAILS.
d = 100 mm x = 50 MPa Fig. 01 d = 75 mm T = 80 MPa 02 Determine the smallest allowable diameter brass rod, of length 3.0m, if the rod is to be twisted through one complete revolution without exceeding a shearing stress of 50 MPa. For brass, G = 39 GPa.
PLEASE DRAW THE FBD. DO NOT COPY YOUR ANSWER FROM OTHER. I WANT TO SEE THE FBD OF INDIVIDUAL DEFORMATIONS ON HOW YOU WILL ARRIVE ON YOUR ANSWER. DRAW FBD ON EACH PLEASE. NOT ONLY ONE FBD