ACTIVITY The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are angle sections with thickness shown in the figure. The working stresses are 70MPa for shear in rivet and 140MPa for bearing stress due to the rivets. How many 19-mm diameter rivets are required to Fasten the said members to the gusset plate? A 306 00 4m B 3m C 96KN 4m 6m 200KN E Am 3m F 96KN 4m H DETAIL OF JOINT B ------ 75X75X6 mm I BC 14 mm thick GUSSET PLATE - 75X75X13 mm P BE

ACTIVITY The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are angle sections with thickness shown in the figure. The working stresses are 70MPa for shear in rivet and 140MPa for bearing stress due to the rivets. How many 19-mm diameter rivets are required to Fasten the said members to the gusset plate? A 306 00 4m B 3m C 96KN 4m 6m 200KN E Am 3m F 96KN 4m H DETAIL OF JOINT B ------ 75X75X6 mm I BC 14 mm thick GUSSET PLATE - 75X75X13 mm P BE

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the resultant load on the most stressed bolt in the eccentrically loaded connections shown, using the elastic method.
22 - please provide a complete answer in a given-required- solution format, thanks!
PROBLEM NO. 2: Two plates each with thickness t = 16mm are bolted together with 6-22mm diameter bolts forming a lap connection. Bolt Spacing are as follows: S₁ = 40mm, S₂ = 80mm, S3 = 100mm. Bolt diameter = 22mm. Use A36 steel. Calculate the allowable strength due to block shear only. I= 16 mm S₁ S₂ S₂ S1 40 80 80 40 18-16mm S-40 S₁-100 S-40
Situation 8: For the connection shown in the figure. Pu = 80 KN, x1 = 200, x2 = 100, y1 = 50, y2 = y3 = y4 = 100 y1 y2 y3 y4 O 80 MPa O 71 MPa O 74 MPa oooo O 86 MPa O 1. Which of the following nearly gives the shearing stress of the most stress bolt? Use 20 mm diameter bolt. x1 O O O x2
The figure shows a roof truss and the detail of connection at joint I. The allowable stresses are 70 MPa for shear and 120 MPa for bearing. How many 20-mm diameter rivets are required to fasten member IG to the gusset plate? What is the required area for member AI if the allowable axial stress is 180 MPa.
7. The bracket shown is welded on one side of a steel column with 800mm of 6mm fillet weld. Determine the maximum shear stress on the weld. If the allowable stress si 400 MPa what is the allowable load that the connection can carry? 44 kN 300 mm F.W. ON NEAR SIDE F.W. ON FAR SIDE F.W. ON FAR SIDE F.W. ON NEAR SIDE 200 mm 200 mm
REVISED PROBLEM: M3 HW 4 4. Six rivets are used in the connection shown in the figure. If both P = 50 kN, what is the minimum diameter P- 50 rivet is necessary so as not to exceed the 70MPA allow shearing stress? What thickness of plate is required so as not to exceed a bearing stress of 140 MPa? 80 mm 80 mm Peso 100 m
2. A staggered riveted connection has rivets arranged as shown. Diameter of rivet is 28 mm. Use AISCINSCP Specs. Fy 248 MPa, Fu = 400 MPa. Determine the distance "S" so that the area area in chain ABCD is equal to the net area in chain ABD. Determine also the tensile capacity of P. 45 10 350 mm 90 90 I mm 60 mm 888
A plate with width of 300mm and thickness of 20mm is to be connected between two plates 12mm thick with same width by 4-25mm diameter rivets a shown. The rivet holes have a diameter 2mm larger than the rivet diameter. The plate is A36 steel with yield strength Fy=248 Mpa and Fu-400MPa. The rivets have nominal shear stress capacity of 165MPa. O 803 O 1490 • Determine maximum load (P1) that can be applied without exceeding design tensile stress in plates (consider yielding and rupture of plates ONLY) in KN O 1180 O 1340 ο ο ο ο ο P3 O 1968 O 590 O 670 O 893 O 707 OO 150 O 1180 P1 P2
Where is/are the location(s) of the maximum transverese shear stress? A simple I-beam is loaded as shown. 20 mm P KN PKN PKN Į Į -C B с D L/4 m L/4 m Midspan at point C Roller at E at the NA Section B at the top fiber Pin A at point C Midspan at point D Roller E at point D L/4 m L/4 m OE 20 mm 20 mm- 250 mm 150 mm 150 mm A
Problem For the frame shown, design the maximum permissible value of P with a factor of safety of 2.5. Design the maximum permissible value of P based on the following conditions: Ultimate tensile strength of each member CD is 300 ksi ✓ Ultimate shear strength of the bolts in A, C, E, and F is 200 ksi ✓ Ultimate bearing strength of member BDE is 150 ksi ✓ Ultimate bearing strength of the support plates is 250 ksi Members CD and BDE have cross-sectional dimensions of 5 in x 3 in (the larger dimension is the width). The diameters of the bolts are as follows: A and B - 1.5 in; C and D - 2 in; E and F - 1 in. 1.5 in. thick Support Plates 2 in thick Support Plate 3 ft B -2 ft- C + D -2 ft- + E -2 ft- -CD has 2 members. One on each side. F
Name: Time you spent to solve the problem HW- 3 ID.: 'Dėtërminë thé forċés in all the members, and state if these memibers are in tension or compression. Use table to arrange your Cal&tlations, show the results on the truss ( if not your witf täke zerở)** 30 N 4m 3 т 15