Problem 912Compute the stresses at A and B on the link loaded as shown in Figure P-912if P = 9000 lb and F = 3000 lb.12 in-6 in 6 in-13 inFA13 in BFigure P-912-12 in-¯¯Â2 in6 inCross-Section

a ) P = 9000 lb and F = 3000 lb Compute the stresses at A and B ? Solid mechanics problem.

Answered: Problem 912 Compute the stresses at A…

Problem 912 Compute the stresses at A and B on the link loaded as shown in Figure P-912 if P = 9000 lb and F = 3000 lb. P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A bridge girder AB on a simple span of length L = 20 m supports a distributed load of maximum intensity q at midspan and minimum intensity g/2 at supports A and B that includes the weight of the girder (see figure). The girder is constructed of three plates welded to form the cross section shown. 500 mm L= 20 m 18 mm 1600 mm 500 mm (a) Determine the maximum permissible load q based upon an allowable bending stress oallow = 130 MPa. Round to the nearest tenth. kN Gmax = (b) Determine the maximum permissible load q based upon an allowable shear stresS Tallow = 55 MPa. Round to the nearest tenth. kN Gmax m
A wooden frame shown below is supported by a tie rod CF and a pin support at A. The diameter of the tie rod CF is 30 mm, and the cross-sectional area of member BD is 900 mm?. The diameters of the pins at A and D are 8 mm and 12 mm, respectively, and each pin is subjected to double shear. If the weight of the bucket hanging from end E is 3 kN, determine (a) The axial stresses in tie rod CF and member BD. (b) The shear stresses in pins A and D. - 0.6 m-0.6 m→ D E 0.6 m V30B 1.2 m F
A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional area of A = 3.7 in.². Assume a = 4.75 ft and b = 5.70 ft. If the normal stress in each member must not exceed 60 ksi, determine the maximum load Pmax that may be supported by the structure. a D Answer: Pmax = i b B E b kips P
A rigid bar XYZ as shown in the figure below is hinged at X and is supported at Y. If the stress in the steel rod is limited to 150 ksi, determine the largest possible load P that can be applied at point Z.
Question 3 of 5 -/ 20 E View Policies Current Attempt in Progress A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 580 mm2. If the stress in the bar must not exceed 330 MPa and the maximum deformation in the bar must not exceed 13 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 4 m, b 2.4 m, and c = 5.2 m. %3! C (1) a Answer: kN P = Attempts: 0 of 1 used Sub Save for Later B.
A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 540 mm?. If the stress in the bar must not exceed 450 MPa and the maximum deformation in the bar must not exceed 20 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 4 m, b = 2.4 m, and c = 5.2 m. (1) B' A a Answer: P = i kN
For the shown Fig., find the maximum shearing stress in bronze part of the shaft. * Steel d= 200mm G= 80GPa Bronze d= 100mm d= 100mm G= 40GPa G= 30GPA 2KN.m Aluminum 8KN.m 3kN.m 3m 2m 1.5m +
8-46. The wide-flange beam is subjected to the loading shown. Determine the stress components at points A and B and show the results on a volume element at each of these points. 500 lb ↓ 2 ft 2 ft 2500 lb B 2 ft 4 ft 3000 lb 0.5 in.- Prob. 8-46 B 6 ft- 0.5 in. 1-4 in T 4 in. 12 in. 0.5 in.
For the beam shown in Figure (1), determine: a) The stresses in rods AB and BC. The cross-sectional area of rod AB is 155 mm2, and for BC is 200 mm?. b) The average shear stress in bolt at pin A. 1500 N S5 15 m 600 N/mt m- -3 m- Figure (1)
A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 520 mm?. If the stress in the bar must not exceed 650 MPa and the maximum deformation in the bar must not exceed 20 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 8 m, b = 4.8 m, and c= 10.4 m. (1) B' a Answer: P = i kN
Q4: For the figure below, determine the principal stresses and show them on a sketch of a properly oriented element. Also, find the maximum shear stresses and show them on a sketch of a properly oriented element. (Consider only the in-plane stresses.) -30MPA 90 MPa -34MPA
A magnesium-alloy rod (E = 6.5 x 10 ksi) of Prob. 3.4-6. diameter d 1 in. is encased by a brass tube (E 15 x 10 ksi) with outer diameter d. = 1.5 in.; both have length. L = 20 in. An axial load P = 10 kips is applied to the resulting bimetallic rod. (a) Determine the normal stresses and , in each material, assuming that the magnesium rod and brass tube are securely bonded to each other. (b) Determine the elongation of the bimetallic rod. P