A PL40 mm X 250 mm (smaller member) is connected to a gusset plate (bigger member) as shown. The diameter of the holes are 25 mm. The pitch and gage of the holes are 50 mm and 75 mm, respectively. The yield strength of the steel is 260 MPa while the ultimate tensile strength of the steel is 400 MPa, Determine the design (LRFD) tensile strength of the tension member in KN. Neglect block shear. H G P P F E

A PL40 mm X 250 mm (smaller member) is connected to a gusset plate (bigger member) as shown. The diameter of the holes are 25 mm. The pitch and gage of the holes are 50 mm and 75 mm, respectively. The yield strength of the steel is 260 MPa while the ultimate tensile strength of the steel is 400 MPa, Determine the design (LRFD) tensile strength of the tension member in KN. Neglect block shear. H G P P F E

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

b. The gusset plate shown in Figure 10 is welded to a vertical member. The gusset plate carries a load of 250 kN acting at a distance of 250 mm from the closest edge of the weld. The weld around the gusset plate is completed in two 140 mm horizontal portions and one 320 mm vertical portion. If the maximum allowable shear stress of the weld is 200 N/mm², detemine the minimum thickness of the weld required. In calculations, the second and higher order terms of the weld thickness for second moment of area calculations may be neglected. 250 kN 140 mm 250mm 140 mm Figure 10 320 mm
10/10 find the tensile stress in upper plate in section 3-3 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM 10 MPа О 12.5 MPa 15 MPa 8.5 MPa O no one O ---.. O- O O 300mm 8 mm
rectanqular seetion with width bz250 and depth h= 500mm is to carcry a A m %3D design bending moment M= 260KN•M, The conerete is of greade e30 and the tensile steel is of HRB400. The tension reinforzce. ment A, is requined.
A fillet-welded Joint of 6mm size is shown in the figure. The welded surfaces meet at 60-90 degree and permissible stress in the fillet weld is 108MPa. The safe load that can be transmitted by the joint is 100mm 50mm
I need the answer as soon as possible
The aluminum rod AB (Gal = 27 GPa) is bonded to the brass rod BD (Gbr = 39 GPa). The portion CD of the brass rod is hollow and has an inner diameter of 40 mm. If the allowable shear stresses for the aluminum and brass are 90 MPa and 70 MPa, respectively, and the allowable angle of twist of the free end A is 6 degrees, determine the maximum permissible value of T
Find the stress in each rods. The 300 mm x 300 mm santrir m 2 m P-30 kN Steel L-0.5m E-200 GP A-500 m 1.5m Bronze L-2m E-70 GPa A-300 mm²
The assembly consists of two A992 steel bolts AB and EF and an 6061-T6 aluminum rod CD. When the temperature is 30°C, the gap between the rod and rigid member AE is 0.1 mm. Assume BF is also rigid. (Figure 1) Figure 400 mm A B 25 mm 50 mm D 0.1 mm 300 mm E 1 of 1 25 mm Part A Determine the normal stress developed in the bolts if the temperature rises to 180°C. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. of = Submit Part B σ₁ = Submit O HA Value Request Answer Provide Feedback ■μÅ Value Determine the normal stress developed in the rod if the temperature rises to 180°C. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. Units Request Answer wwwww Units ? wwwww Review ? Next >
2) Find the axial stresses of menbers FD, GD, GE State if it is tensile or Compressive. 4M 3M A LE 3m G 20 RN Go KN