The Load P = 2600 lb is applied on a five bolt truss. If the average shear stress in the bolts must be limited to 27 ksi, Determine the minimum bolt diamete

Q: A plate having a width of 400 and a thickness of 20mm is to be connected to two plates with…

A:

Q: The five-bolt connection must support an applied load of P = 149 kips. If the average shear stress…

A:

Q: A 12.5 mm x150 mm plate is connected to a gusset plate having a thickness of 9.5 mm.Diameter of…

A: A 12.5 mm x150 mm plate is connected to a gusset plate having a thickness of 9.5 mm.Diameter of bolt…

Q: The plate welded to the end of the I-beam is fastened to the support with four 10-mm-diameter bolts…

A: The data given is a I beam inclined at 40o subjected to a 30 kN force, and is supported by two bolts…

Q: A 20-mm-thick plate is bolted to the flange of a T-beam to form a -200 mm 20 mm built-up beam. If…

A: Calculate the moment of inertia of I section…

Q: Two plates are held together by 3, 23 mm diameter bolts. If a 11 kN load is applied to the plates in…

A: Number of bolt = 3 Diameter of bolt (d) = 23 mm Load (P) = 11KN

Q: 2. A steel plate is 360 mm wide and 20 mm thick with four bolts hole into the place as shown in the…

A: Answer  Given data  b= 360 mmt=20 mmNo. of bolts- 4

Q: PROBLEM SOLVING 2 The plates are connected by 12-mm bolts in Figure 5. The maximum axial stress of…

A:

Q: Two bolts are used to lap points two steel plates. Tensile force on the plate is 45KN. Determine the…

A:

Q: Five bolts are used in the connection between the axial member and the support. The ultimate shear…

A: We will take case of two way shear and use formula of shear strength considering factor of safety.

Q: A steel bar is attached to a wood support beam with four 22 mm diameter lag screws, as shown in the…

A: Given Diameter of screw, d = 22 mm Number of screws, n = 4 Width of steel bar, b = 69 mm Thickness…

Q: A steel plate is to be attached to a support with three bolts. The cross-sectional area of the plate…

A: We have to find out the minimum bolt diameter required to develop the full strength of the plate.

Q: For the connection shown, the bolt diameter is d = 15 mm.  The average shear stress in the bolts…

A:

Q: The pin in the image shown below must transfer an axial tension force of 12.7 kN. Calculate the…

A: First we need to find the value of yield strength using steel through internet.

Q: afe strength of a 5/16 in. fillet weld if it's actual length is 3 1/2 in. and the allowable unit…

A:

Q: The given angle bar L125x75x12 with Ag = 2,269 sq.mm. is connected to a gusset plate using 20 mm…

A:

Q: Two plates each with thicknessF16mm are bolted together with6 -22mm dimater bolts forming a lap…

A: Permissible stress is normally refers the allowable stress or allowable strength is the maximum…

Q: For the welded tension member shown in the figure, determine the shear lag factor, U; the net area,…

A:

Q: The angle L 8 x 8 x ½ in tension shown in the figure below must resist a service dead load of 35…

A:

Q: With the dimensions already given, determine the allowable value of the tensile load P, considering…

A: Answer  (1) Allowable normal stress at the two vertical bolts (1) and 92) is 160 Mpa Allowable…

Q: Determine the design tensile strength of the plate (200 × 100) mm connected to a 12 mm thick…

A: Given: The dimension of the plate is 200 mm x 100 mm. The thickness of plate is gusset is 12 mm. The…

Q: For the welded tension member shown in the figure,determine the shear lag factor, U; the net area,…

A:

Q: The five-bolt connection shown must support an applied load of P = 330 kN. If the average shear…

A:

Q: Part A If the bolt is subjected to a compressive force of P = 21.9 kN, determine the magnitude of…

A: Length of bronze and steel rod is same.The change in length of steel is equal to the change in…

Q: The bolted connection shown must support an applied load of P = 5300 kN. The average shear stress in…

A: The values and diagram given in the question are as follows: Applied load(P)=5300 kN or 5300*103 N…

Q: 500 mm B 500 mm- 2000 mm 1000 kN 200 mm- Section AB 200 mm

A:

Q: The five-bolt connection shown must support an applied load of P = 371 kN. If the average shear…

A: Given Load 371 kNStress 174 MPaNumber of bolts 5To find out Minimum diameter

Q: 2. A steel plate is 360 mm wide and 20 mm thick with four bolts hole into the place as shown in the…

A:

Q: Determine the design tensile strength of plate (200 x8 mm) connected to 10-mm thick gusset using 20…

A: Given, Yield stress of the plate fy=250 N/mm2 d=20 mm Diameter of the hole do=20+1=21 mm  Ultimate…

Q: Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will…

A:

Q: Two plates are held together by 4, 10 mm diameter bolts. If a 26 kN load is applied to the plates in…

A:

Q: A single unequal angle 100 x 75 x 6 is connected to a 10 mm thick gusset plate at the ends with six…

A: Given data, For a single unequal angle 100x75 is connected to a 10 mm thick gusset plate at the ends…

Q: A 76 mm x 76mm x 6mm angular section is welded to a gusset plate having a thickness of 8mm as shown…

A: Solution: Given: Section: 76 x 76 x 6 mm  plate thickness = 8 mm length of the weld = 65+76+125=266…

Q: One bolt 3 4 in-16 UNF × 2 1 2 in. SAE grade 5 is subjected to a P load of 6 kip at a tension joint.…

A: Given:- One bolt 3/4 in-1 UNF ×212 in. SAE grade 5 is subjected to a load The magnitude of the load…