The uniform beam is supported by two rods AB and CD that have cross-sectional areas of 12 mm? and 18 mm², respectively. Determine the normalstress in each rod in MPa.ВDd4kN/mA5mA 200(в) 466.67355.56D) 533.33

Answered: Image /qna-images/answer/423dc405-666d-447a-9255-8aa197d129d7.jpg

Answered: The uniform beam is supported by two…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The segment AB of the steel torsion bar is a cylindrical tube of constant 2-mm wall thickness. Segment BC is a square tube with a constant wall thickness of 3 mm. The outer dimensions of the cross-sections are shown in the figure. The tubes are attached to a rigid bracket at B, which is loaded by a couple formed by the forces P = 17 kN. Determine the maximum shear stress in the shaft. Take G = 75 GPa. P 1.2m C 100 mm 100 mm t = 3 mm 1.2m 80 mm B 300 mm A -t = 2 mm Important reminder: The formulas derived for thin-walled tubes are just approximations. So, for the case of hollow circular tubes with constant thickness, you should still use Tc/J and TL/JG to solve for the shear stress and angle of twist, respectively.
Set-up the overall stiffness matrix necessary to compute the nodal displacements at B and C. Compute the member forces of AB and BC and then determine the reactions at A and C. El=constant. 30 KN/m A 6m B 4 m
Situation 5 - A steel drive shaft is 1.80 m long and its outer and inner diameters are respectively equal to 56 mm and 42 mm. The shaft transmits 180 kW while rotating 1t 1800 rpm. Use G = 77 GPa. 36. What is the applied torque in N-m? А. 1008 В. 849 37. Compute the maximum shearing stress in MPa. А. 40.5 В. 42.8 38. Compute the angle of twist in degrees. A. 1.72 В. 1.94 C. 637 D. 955 C. 27.1 D. 36.1 C. 2.05 D. 1.29
The bar AB is supported by a frictionless inclined surface at A and a 7/8 in.- diameter pin at B that is in double shear. Determine the shear stress in the pin when the vertical 2000-lb force is applied. Neglect the weight of the bar. 2000 lb 5 ft В 5 ft A 10° 30°
If M, = 285 kip-ft, find the magnitude of the bending stress at a point H For the beam cross section, assume a = 9 in. b= 12 in. d= 31 in r= 45 in. The centroid of the cross section is located 14.16 in. below the uppermost surface of the beam. The moment of inertia about the z axis is 26227 in 4
Set-up the overall stiffness matrix necessary to compute the nodal displacements at B and C. Compute the member forces of AB and BC and then determine the reactions at A and C. El=constant. 30 KN/m 6 m. В 4 m
In the figure shown, El is contant. Determine the Moment at CB, Mcg, in kNm.
A beam has the cross section shown (thin-walled profile). The shear center is at a distance, e = 32.7 mm from the web, IEN = 1134000 mm4. If a force V = 30 kN is applied, passing through the shear center as shown, determine the nearest value of the shear stress in the web at C. |5 mm 3 mm 3 mm 30 mm D 80 mm 30 mm mm E F 55 mm а. 117 МPа O b. 70 MPa Ос. 138 МРа O d. 94 MPa
6.71 A simply supported beam has uniform cross- section, b= 100 mm, d = 200 mm, throughout its length. The beam is subjected to a maximum bending moment of 6 x 107 N-mm. The corresponding bending stress developed in the beam is
If Mz = 340 kip-ft, find the magnitude of the bending stress at a point H. For the beam cross section, assume a = 9 in. b = 12 in. d = 30 in. r = 4.5 in. The centroid of the cross section is located 13.71 in. below the uppermost surface of the beam. The moment of inertia about the z axis is 23897 in.4.
The shaft in the figure has a hollow part from B to A and is solid throughout C to B. The hollow segment is 8mm thick and the shaft has an outer diameter of 80mm. Determine the maximum shear stress developed in the shaft. If B is the midpoint of the 2-meter shaft, and G = 75 Gpa, determine the angle of twist of A with respect to C. PROBLEM 1 B 4 kN-m 2 kN-m
USE DOUBLE INTEGRATION METHOD.

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

The uniform beam is supported by two rods AB and CD that have cross-sectional areas of 12 mm² and 18 mm², respectively. Determine the normal stress in each rod in MPa. D d. 4kN/m A 5m A 200 B) 466.67 C) 355.56 D) 533.33