If M₂ = 280 kip-ft, find the magnitude of the bending stress at a point H. For the bear cross section, assume a = 9 in. b = 12 in. d = 28 in. r = 4.5 in. The centroid of the cross section is located 12.83 in. below the uppermost surface of the bear. The moment of inertia about the z axis 19668 in.4. M. M. X ڈے

If M₂ = 280 kip-ft, find the magnitude of the bending stress at a point H. For the bear cross section, assume a = 9 in. b = 12 in. d = 28 in. r = 4.5 in. The centroid of the cross section is located 12.83 in. below the uppermost surface of the bear. The moment of inertia about the z axis 19668 in.4. M. M. X ڈے

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 3 Determine the deflections in horizontal and vertical directions at point C and the reactions at supports A and B of the truss shown in Figure (3) using the stiffness method. Take E = 210 GPa and A = 170 mm² for all members. 24 KN 3.00 m 4.00 m Figure (3) C B 18 KN
value of the slope (rotation) at the end of a cantilever beam with a distributed force, w = 8.9kN / m The beam has the following properties: E = 200GPa , I = 467 cm^4 L= 4.8 m.
HI! HELP ME WITH THIS PLEASE. THANK YOU VERY MUCH!
Using stress transformation equation
If M, = 285 kip-ft, find the magnitude of the bending stress at a point H For the beam cross section, assume a = 9 in. b= 12 in. d= 31 in r= 45 in. The centroid of the cross section is located 14.16 in. below the uppermost surface of the beam. The moment of inertia about the z axis is 26227 in 4
6.71 A simply supported beam has uniform cross- section, b= 100 mm, d = 200 mm, throughout its length. The beam is subjected to a maximum bending moment of 6 x 107 N-mm. The corresponding bending stress developed in the beam is
If Mz = 340 kip-ft, find the magnitude of the bending stress at a point H. For the beam cross section, assume a = 9 in. b = 12 in. d = 30 in. r = 4.5 in. The centroid of the cross section is located 13.71 in. below the uppermost surface of the beam. The moment of inertia about the z axis is 23897 in.4.
Rigid 40° B 8ft 2000 lb (a) The rigid bar BC in the figure is supported by the steel rod AC of cross-sectional area 0.25in^2. Find the vertical displacement of point C caused by the 2000-lb load. Use E=29x106psi for steel.
2. The 2- dimensional truss shown in FIGURE Q2 is made of material that has a modules of elasticity E = 150×10° N/m?. The cross sectional area of each member is 0.01 m². Forces P1 and P2 are acting as shown, Wall (e= 40°, P;= 8 kN) 2 (a) (b) 40 (c) 309 P1 P= 2kN 4m FIGURE Q2 a. You are required to design TWO (2) different system's fixing type of nodes 2, 3, and 4 to the wall. Then recommend the best option that provides the lowest displacement at node 1 by perfoming complete calculations to justify your recommendation. b. After the client approved your recommendation in (a), it was found that the displacements occurred at node 1 is still high. As a result, you are required to modify the truss design in order to reduce the displacement at node 1 by minimum 15% on a condition that modules of elasticity, and the force remain unchanged. Justify your recommendation.
Using Virtual Work Method For the truss shown: a) compute the vertical components of the displacement of joint C. In addition to the load , the temperature of member BD is subject to a temperature increase of 60°F. For all bars, E = 29,000 kips/in.2, A = 4 in.2, and α = 6.5 × 10−6 (in./in.)/°F b) If bars AB and BD are fabricated 3/4 in . too long, compute the vertical displacement of "joint C" . Neglect all the applied loads.
Q2 / The cross sectional area of each member of the truss as shown in the figure below 1.75 in² and E = 29(10³)ksi, determine the vertical displacement at joint D due to radiant heating of member FD is subjected to an increase in temperature from 20° F C to 110° F, take a = 0.75(10)/F, and member CD would be decreased 0.2 in use Method of Virtual Work. (P in k) 4 m P=9 PLE 3 m B 3 m C VP 3 m D
solve fast