The pressure force P acts on the column given in the figure from the point P. a) Find the neutral axis. b) Find the stresses in P. c) Find the value of the largest P force for o safety = 12000 N/cm2. Here ex = 3 cm, ey = 6 cm. D X A 15 cm > B 30 cm

The pressure force P acts on the column given in the figure from the point P. a) Find the neutral axis. b) Find the stresses in P. c) Find the value of the largest P force for o safety = 12000 N/cm2. Here ex = 3 cm, ey = 6 cm. D X A 15 cm > B 30 cm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Rigid bar ABCD is supported by two bars as shown in Figure P2.7. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in bar (2) is measured as –3,300 um/m. Use the dimensions L1 = 1,600 mm, L2 = 1,200 mm, a = 240 mm, b = 420 mm, and c = 180 mm. Determine:(a) the normal strain in bar (1).(b) the normal strain in bar (1) if there is a 1 mm gap in the connection at pin C before the load is applied.(c) the normal strain in bar (1) if there is a 1 mm gap in the connection at pin B before the load is applied.
A cylindrical pressure vessel having a radius r = 14 in. and wall thickness t = 0.625 in. is subjected to internal pressure p = 375 psi. In addition, a torque T = 90 kip-ft acts at each end of the cylinder (see figure). (Assume that the structures behave linearly elastically and that the stresses caused by two or more loads may be superimposed to obtain the resultant stresses acting at a point. Consider both in-plane and out-of-plane shear stresses unless otherwise specified.) T T (a) Determine the maximum tensile stress o, and the maximum in-plane shear stress T in the wall of the cylinder. max max (Enter the magnitudes in ksi.) ksi = Tmax ksi (b) If the allowable in-plane shear stress is 4.5 ksi, what is the maximum allowable torque T? (Enter the magnitude in kip-ft.) | kip-ft (c) If T = 150 kip-ft and allowable in-plane shear and allowable normal stresses are 4.5 ksi and 11.5 ksi, respectively, what is the minimum required wall thickness (in inches)? in.
4. A nylon [E = 360 ksi; v= 0.4] rod (1) having a diameter of dl = 2.50 in. is placed inside a steel [E = 29,000 ksi] tube (2) as shown in Figure P3.7. The inside diameter of the steel tube is d2 = 2.52 in. An external load P is applied to the nylon rod, compressing it. At what value of P will the space between the nylon rod and the steel tube be closed? Nylon rod (1)- Steel tube (2)
From the force system shown, determine the the horizontal component of the force T Q = 200 lb Y. P = 722 lb 60 20 F = 448 Ib T = 400 lb
T·r T (from torsion) = Tr4 J ="- (Solid rod) F Onormal = A o (from bending) M•y - (Solid rod) The solid rod shown in the figure below has diameter of 1.25 in. If it is subjected to the force of 60 lb, determine the state of stress at point A using the principle of superposition. Neglect the weight of the rod, and the stress due to the I %3D I 4 transverse shear force. 60 lb k-10 in.- 15 in. Front View -20 in. В
The cross-sectional dimensions of a beam are shown. The internal bending moment about the z centroidal axis is M₂ = +3.51 kip-ft. Assume b = 7.125 in., d = 5.25 in. and t = 0.75 in. Determine: (a) the maximum tension bending stress in the beam. (b) the maximum compression bending stress oc in the beam. Answers: (a) OT = i ) oc = i t b y K H ksi ksi.
The uniform forces U and P are applied to a plate with dimensions of 500mm x 400mm and a thickness of 10 mm as illustrated. Consider the linear elastic behavior, 200GPa Young's modulus, and 78GPa shear modulus. The plate is subjected to a uniform force U with an undetermined magnitude and direction and a uniform tensile force P=50KN. X 500 mm 400 mm A. What is force U, in kN, if deformation along y is zero? Is it a compressive or tensile force? B. What is the x-axis deformation, in mm? Is the dimension growing or shrinking?
The two bars shown in the figure are used to support a load P. When unloaded, joint B has coordinates (0, 0). After load P is applied, joint B moves to the coordinate position (0.35 in., -0.55 in.). Assume a = 13 ft, b = 7 ft, and h = 10 ft. Determine the normal strain in each bar. A Answers: EAB= EBC= i i a B P b με με
Q1) A stat of stress is specified in Figure. By using Mohr's circle determine the normal and shearing stresses on the principal plane, and sketch the results. 18 MPa 60 MPa 15 MPA
The plate has a thickness of 20 mm and the force P = 5 kN acts along the centerline of this thickness such that d = 150 mm. (Figure 1) Figure d‡ 200 mm a 1 of 1
The cross-sectional dimensions of a beam are shown in the figure. (a) If the bending stress at point K is 35 MPa (C), determine the internal bending moment Mz acting about the z centroidal axis of the beam. (b) Determine the bending stress at point H. The bending stress is positive if in tension and negative if in compression. 85 mm 4 mm TT K 55 mm H 4 mm 45 mm 4 mm Answers: (a) Mz = UN-m (b) OH = JMPA
Part of a two story building is shown in the figure in which a concerte column and a steel column are used in the first and second floor. The compressive force on the roof of the second floor is PC = 400 kN. The compressive force on the first floor is PB = 310 kN. The steel [Esteel = 200 GPa] column is a wide angle steel shape that has a cross section area of A2 = 1850 mm2. The concrete [Econcrete = 30 GPa] column has a circular section with a diameter of d = 530 mm.[L1 = 4.8 m, L2 = 5.8 m] What is the displacement of the column at B?in mm What is the displacement of the column at C? In mm