ne bar AB iIs supported by a frictionless inclined surface at A and a 7/8 in.- diameter pin at B that is in double shear. Determine the shear stress in the pin when the vertical 2000-Ib force is applied. Neglect the weight of the bar.

Q: 5-91. The A992 steel shaft made from two segments. AC has a diameter of 0.5 in. and CB has a…

A: Diameter of AC shaft =0.5 in Diameter of CB shaft =1.0 in Uniform distributed torque =60 lb·in/in…

Q: Determine the maximum load P that can be applied to the beam if the bearing plates A' and B' have…

A: Given: Required : Maximum value of P

Q: A stepped shaft ACB having solid circular cross sections with two different diameters is held…

A:

Q: Answer

A:

Q: Compute the maximum load P (in kiloNewtons) so as not to exceed the compressive stress of 75 MPa and…

A: To find out the maximum load P that can carry maximum tensile load 100 Mpa and compressive load 75…

Q: Мо В C A LAB LBC

A:

Q: *1-44. The 150-kg bucket is suspended from end E of the frame. If the diameters of the pins at A and…

A:

Q: For the beam with cross-section shown, the allowable flexural stresses for tension and compression…

A: TF1=20, BF1=3x20=60, Tw=20, Dw=8x20=160, TF2=20, BF2=10x20=200, D=a+8a+a=20+160+20 = 200

Q: Determine the safe span that a 100 * 150 mm purlin would have if it has a spacing 800 mm on centers,…

A: According to given data  a 100 * 150 mm purlin if it has a spacing 800 mm on centersa roof load of…

Q: CLO 1: Use G = 11.6 x 10 ksi for the circular shafts. Determine the %3D maximum torsional shear…

A: Option 8.16 is correct one for first image and explaination in below image

Q: *1-44. The 150-kg bucket is suspended from end E of the frame. If the diameters of the pins at A and…

A: Given : Weight of bucket = 150 kg Dia of pin A = 6mm Dia of pin D = 10 mm To Find : Average shear…

Q: A rectangular beam has the following properties: fc'=28MPa fy=270MPa b=300mm d=450mm As=4 of…

A:

Q: *1-44. The 150-kg bucket is suspended from end E of the frame. If the diameters of the pins at A and…

A:

Q: a) Find minimum diameter nceded if the allowabe shear stress is 140 Mpa and the otation of point A…

A: Solution:-  We know that torsion equation is, TJ=τr=GθL here, net torsion is , T=T3-T1+T2  =10-4+2…

Q: PDL = 15 kN/m , PLL = 5 kN/m 2 - 16m 4m 5m 3m

A:

Q: 1. Draw the shear and moment Diagram of the beam. 2. Determine the maximum compressive stress of the…

A: Given- A continuous beam of total span 12m and subjected to a UDL of 45Kn/m over the entire span.…

Q: Derive the relationship for maximum and minimum shear stress in a wide flange I-Section. Also…

A: Given: V=50KNflange width=300mmflange depth= 40mmweb thickness=40mmweb depth=220mm   Calculate the…

Q: A stepped shaft ACB having solid circular cross sections with two different diameters is held…

A:

Q: A tubular post of outer diameter d₂ is guyed by two cables fitted with turnbuckles (see figure).…

A:

Q: a). What is the minimum diameter of a solid 6m steel shaft that will carry a earing stress of not…

A: solution Leth the diameter of shaft =dLength L =6mts shearing stress ζ=45Kpa and torque T=15KNmwe…

Q: Am 60 300 mm 300 mm 300 mm

A:

Q: Three forces are applied to lever ABD. (a) Draw Mohr's Circle for Point H, (b) determine the max…

A: free body diagram at H Draw Bending stress diagram Shear stress diagram

Q: Problem No. 3. The pin at C is with a diameter C. Assume that the pin at C is supported as stated in…

A:

Q: 5. The lap joint shown is fastened by two %-in.- diameter rivets. Calculate the maximum safe load P…

A: (As per student demand, Solution to 5 ) To find:Calculate the maximum safe load P

Q: A solid 1.500-in.-diameter steel [G= 13,000 ksi] shaft is subjected to torques TB - 265 lb-ft and…

A: Given: The diameter of the shaft is 1.5 in. The value of G is 13000 ksi. The torque TB is 265 lb-ft.…

Q: 1-39 The lever is held to the fixed shaft using a tapered pin AB, which has a mean diameter of 6 mm.…

A: Given:Pin AB mean diameter,dm=6 mm

Q: Determine the largest load P that can be applied at A when 0 = 50° , knowing that the allowable…

A: Solution: Given data: dia =10 mmθ=50°

Q: The mass of the block and thus the total downward pull of gravity are the same on slopes with angles…

A: Ans: True Explanation: given in step 2

Q: 25M meter of the column in the ne nber of diameter 28mm longitu

A: Given:- deadload=1530kN live load-1420kN 12mm dimaeter  f'c=30MPa fy=425MPa To find:- a) diameter of…

Q: a) What is the distance to centroid (x）?   Please enter answer in mm and to 1dp. b) For the same…

A:

Q: A horizontal beam AD with cross-section of 3800 mm² is supported by a wire at C and carries a load…

A:

Q: stress in the shaft is 3,370 magnitude in Ib-in.) de in Ib-in.

A:

Q: 4 ft C B ITI

A:

Q: thickness "t" of the steel plate if the

A:

Q: (a) Calculate the maximum shear stress Tmar in the shaft. (b) Calculate the angle of twist 8 (in…

A:

Q: In reinforced beam having a width of 300 mm and an effective depth of 600 mm, carries a moment of 60…

A:

Q: Two C 310 x 37 channels are riveted together by pairs of 16 mm rivets spaced 180 mm apart along the…

A:

Q: Q 3: -Knowing that the bracket AB has a uniform thickness of in., determine (a) the principal planes…

A: The bracket is shown in the figure.

Q: X C The 5.4-in diameter steel shaft AB is attached into the rigid wall at C and supported by a…

A: From figure, we observe that B is fixed So, Torque at B will be T = x times P = 2.47 P Also, Shear…

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.