In the figure below, the 1300-kg uniform bar AB is suspended from two cables AC and BD each with a cross-sectional area of 410mm². The stresses in AC and BD are limited to 110MPa and 53MPa, respectively. D 1.7m 1.7m x-P B 3.5m7 Find the magnitude P of the largest additional vertical force that can be applied to the bar. kN in 2 decimal places

In the figure below, the 1300-kg uniform bar AB is suspended from two cables AC and BD each with a cross-sectional area of 410mm². The stresses in AC and BD are limited to 110MPa and 53MPa, respectively. D 1.7m 1.7m x-P B 3.5m7 Find the magnitude P of the largest additional vertical force that can be applied to the bar. kN in 2 decimal places

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A triangular table is in equilibrium and it carries vertical loads as shown. If the supports D, E, and F only carry vertical reactions, what is the axial force at member BE (in kN)? 70 KN SokN 2m 1.SM A 2m 2m
Figure 1 shows a pin-connected truss system with pin supports at points A and B. Member AC has an area of 60 mm², E= 200 GPa, and yield stress oy= 150 MPa; Member BC has an area of 35 mm², E= 200 GPa, and yield stress oy= 200 MPa. A force is applied horizontally at point C as shown in the figure, with corresponding displacement A. Draw the complete F versus A response up to collapse and calculate the over-strength of the system. A B mom топп 60° 2 m F, A C
Q2: For the beam shown in Figure (2), determine transverse shear stresses at points E, F and G on the cross section. The load P-100 KN and INA = 470016 mm*. 12 mm T A D B 0.2 m 0.4 m- 0.2 m 6 m Figure (2) 4mm 96 mm 48 mm 12 mm
3. The rigid bar BDE is supported by two links AB and CD. Link AB is made of steel (E=200 GPa) and has a cross-sectional area of 700 mm'; link CD is made of aluminum (E=70 GPa) and has a cross sectional area of 500 mm. For the 28 kN force shown, deflection at E. A 0.4 m 0.3 m 28 kN D 0.25 m 0.60 m
7. The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the value of torque T that can be applied to the ends of the shaft without exceeding a shear stress of 70 MPa or an angle of twist of 2.50° in the 3.50-m length. Use G = 83 GPa for steel. 100 mm 70 mm 70 mm T A - 2.00 m 1.50 m
An I shape cross-section is subjected to the moment M = 8.4 kN.m. Determine the stress at point A. Set θ = 28°. Present your answer in MPa. The moments of inertia are Iz = 31.846 x 106 mm4 and Iy = 3.346 x 106 mm4.
Q3(b) Figure Q3(b) shows a 100 mm solid steel cylinder that is built into the support at C and subjected to the torques Ta and Tp. (i) Determine the maximum shear stresses in segments AB and BC of the cylinder. (ii) Compute the angle of rotation of end A. Given G=83 GPa for steel.
The 919-kg uniform bar AB is suspended from two cables AC and BD each with cross-sectional area 321 mm2. Find the location x (in mm) of P that can be safely applied to the bar if the stresses in AC and BD are limited to 112 MPa and 57 MPa, respectively. Express your answer in two decimal places.
A tied column 350 mm x 600 mm in cross section is reinforced with 6-28 mm Ø bars arranged as shown in the figure. It is assumed that the column section has a strain on its compression edge equal to 0.003 and has a tensile strain of +0.002 on its outer edge. f = 27.6 MPa. fy = 414.6 MPa. 350 mm 62.5 Tension Bars 600 mm 475 6-28 mm Ø 62.5 Compression Bars - Determine the total compressive force of the steel reinforcement considering that its compressive stress is reduced by 0.85 f' to account for the holes in the concrete. 2 Determine the nominal axial load that causes this strain distribution in the column section. 3 Determine the nominal moment that causes this strain distribution in the mn section.
Pin-connected rigid bars AB, BC, and CD are initially held in the positions shown by taut wires (1) and (2). The bar lengths are a = 36 ft and b = 27 ft. Joint Cis given a horizontal displacement of 5.7 in. to the right. (Note that this displacement causes both joints B and C to move to the right and slightly downward.) What is the change in the average normal strain in wire (1) after the displacement? B (1), a (2) Answer: = i (0)
Which of the following is the nearest value for the force at member CD? a. 4 kN compression b. 6 kN tension c. 6 kN compression d. 4 kN tension
A P = 10 kip 1.5 ft B C 2 ft The bars in the structure to the left are pinned and have circular cross-sections. The diameter of the cross- section is 1.5 inches. The bars are made of steel, which has an elastic modulus of 29,000 ksi. A point force of 10 kips is applied at point C, as shown. What is the change in length of member BC? Is the bar getting longer or shorter?