A shaft ABCD 70 mm in diameter is subjected to torques of 1500 N-m at B and 1100 N-m at C acting in the same direction. AB is 4m long, BC is 2m long and CD is 3m long. Supports A and D are unyielding and G = 80,000 MPa. (a) Calculate the maximum shearing stress of the shaft, (b) Find the rotation between A and C in degrees.

A shaft ABCD 70 mm in diameter is subjected to torques of 1500 N-m at B and 1100 N-m at C acting in the same direction. AB is 4m long, BC is 2m long and CD is 3m long. Supports A and D are unyielding and G = 80,000 MPa. (a) Calculate the maximum shearing stress of the shaft, (b) Find the rotation between A and C in degrees.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A solid 1.750-in.-diameter steel shaft is subjected to torques TB = 285 lb-ft and TD= 115 lb-ft, acting in the directions shown. If the allowable shear stress in the shaft is 22 ksi, determine the maximum torque TC that can be applied to the shaft.
A simply supported wood beam that is 4.2 m long carries a 49 kN concentrated load at B. The cross-sectional dimensions of the beam are b = 130 mm, d = 420 mm, a = 65 mm, and c = 40 mm. Section a – a is located at x = 0.7 m from B. (a) At section a – a, determine the magnitude of the shear stress in the beam at point H. (b) At section a – a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entire span. (d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length
A simply supported wood beam that is 4.2 m long carries a 49 kN concentrated load at B. The cross-sectional dimensions of the beam are b = 130 mm, d = 420 mm, a = 65 mm, and c = 40 mm. Section a–a is located at x = 0.7 m from B.(a) At section a–a, determine the magnitude of the shear stress in the beam at point H.(b) At section a–a, determine the magnitude of the shear stress in the beam at point K.(c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entire span.(d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length.
A compound shaft consists of segment (1), which has a diameter of 1.5 in., and segment (2), which has a diameter of 2.2 in. The shaft is subjected to a tensile axial load of P = 14 kips and torques TA = 5 kip·in. and TB = 34 kip·in., which act in the directions shown. Determine the normal and shear stresses at (a) point H and (b) point K. For each point, show the stresses on a stress element.
A compound shaft consists of segment (1), which has a diameter of 1.5 in., and segment (2), which has a diameter of 1.9 in. The shaft is subjected to a tensile axial load of P = 17 kips and torques TA = 7 kip-in. and Tg = 28 kip-in., which act in the directions shown. Determine the normal and shear stresses at (a) point H and (b) point K. For each point, show the stresses on a stress element. TB TA ■K Answer: Point H: 0x = Txy = Point K: Txy = A (1) ■H ksi ksi ksi ksi ksi ksi B Ⓡ
1. We have a truss structure with a hinge on the left and a roller on the right. (Use method of moments ONLY for finding the members and use the numbered name only for each member) 30.00" a) Find the force acting on members 2, 3, 7, 9, 14, 15. (Indicate Compression or Tension) b) Determine the normal stress @ members 2, 3, 7, 9. (Use figure 2 for cross-sectional area) P/2 30.00" T IP 30.00" T Figure 1 30.00" P/2 30.00" P/2 10.00" 20.00" 2.00" 0.20" Figure 2 0.20" 2.00" 0.20"!
A compound shaft consists of segment (1), which has a diameter of 1.0 in., and segment (2), which has a diameter of 1.3 in. The shaft is subjected to a tensile axial load of P = 16 kips and torques TA = 14 kip·in. and TB = 32 kip·in., which act in the directions shown. Determine the normal and shear stresses at (a) point H and (b) point K. For each point, show the stresses on a stress element.
1. We have a truss structure with a hinge on the left and a roller on the right. (Use method of moments ONLY for finding the members and use the numbered name only for each member) 30.00" a) Find the force acting on members 2, 3, 7, 9, 14, 15. (Indicate Compression or Tension) b) Determine the normal stress @ members 2, 3, 7, 9. (Use figure 2 for cross-sectional area) P/2 30.00" D foo 30.00" Figure 1 30.00" (10 N -30.00" P/2 P/2 10.00" 20.00" 2.00" 0.20" Figure 2 0.20" 2.00" 0.20"
1
len 1
The pole is supported by a pin at B and A-36 steel guy wire AC. If the wire has a diameter of 0.2. Modulus of Elasticity of Steel = 200GPA or 29x103 ksi Poisson's ratio of steel=0.321 3 ft 30 D 2.5 kip 4 ft B 1. At what angle is the principal stresses on pole BC? Use Mohr's Circle. 2. What is the principal stress in pol BC? Use Mohr's Circle 3. Draw the stresses on a unit element acting on 35-degree clockwise direction of pole BC. Use Mohr's Circle. 4. What are the principal stresses in point D? Use Mohr's Circle. (answer in ksi) 5. At what angle is the principal stresses acting on point D? Use Mohr 's Circle. 6. Draw the stresses on a unit element acting on 35degree-clockwise direction of point D. Use Mohr's Circle. (answer in ksi)
2. The hinge support at A and steel rod at B support the horizontal rigid bar (neglect the weight of the bar) as shown. Determine the maximum vertical force P that can be applied at the end of the bar at C if the allowable stress in the steel rod is 35 ksi and the vertical displacement at C is limited to 0.12 in. Use 2 decimal places. (25 pts) steel L = 4 ft A = 0.5 in? E = 29 × 10° psi P =? A B C 3 ft 2 ft