A compound shaft consists of segment (1), which has a diameter of 1.4 in., and segment (2), which has a diameter of 2.2 in. The shaft is subjected to a tensile axial load of P = 24 kips and torques TA-8 kip-in. and Tg = 34 kip-in., which act in the directions shown. Determine the normal and shear stresses at (a) point H and (b) point K. For each point, show the stresses on a stress element.

A compound shaft consists of segment (1), which has a diameter of 1.4 in., and segment (2), which has a diameter of 2.2 in. The shaft is subjected to a tensile axial load of P = 24 kips and torques TA-8 kip-in. and Tg = 34 kip-in., which act in the directions shown. Determine the normal and shear stresses at (a) point H and (b) point K. For each point, show the stresses on a stress element.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The compound shaft consists of bronze and steel segments, both having 120-mm diameters. If the torque T causes a maximum shear stress of 100 MPa in the bronze segment, determine the angle of rotation (in degrees) of the free end. Use G = 83 GPa for steel and G = 35 GPa for bronze.
2 An aluminum tube of outer diameter R2 = 50 mm is heated such that it is mounted over a steel shaft of radius. R1 = 30 mm as shown in the figure, The length lof member is 3 m. MT R Ri (1) If a G = 77.2 GPa, G2 = 27 GPa, and torque of MT = 76 kN.m is applied to induce twisting in the member, Determine the maximum shear stress in shaft 1. Select the correct response:
A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid brass shaft with an allowable shear stress of 66 MPa. Segment (2) is a solid aluminum shaft with an allowable shear stress of 85 MPa. If a torque of Tc = 27500 N-m is applied at C, determine the minimum required diameter of the brass shaft d₁ and the aluminum shaft d₂. Tc Answers: d₁ = d₂ = i i (2) (1) B A mm mm
The bell-crank mechanism is in equilibrium for an applied load of P = 38 kN. Assume that a = 260 mm, b = 170 mm, and 0 = 64°. The pin at B has a diameter of d = 29 mm, and the bell crank has a thickness of t = 12 mm. Calculate the average shear stress in the pin at B. T= Bell crank A a B Support bracket MPa B F₁ F
The rectangular bar carries a load of P = 62 kN and is connected to the support bracket with a circular pin. The pin has a diameter of d - 27 mm. Each leg of the bracket has a thickness of t = 16 mm. Determine (a) the shear stress in the pin. (b) the bearing stress between the pin and the bracket. P Rectangular bar Support bracket
9
A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional area of A= 2.9 in.2. Assume a = 3.50 ft and b=4.20 ft. If the normal stress in each member must not exceed 25 ksi, determine the maximum load Pmax that may be supported by the structure. D Answer: Pmax= i b B b kips
A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional area of A = 2.6 in.². Assume a = 4.75 ft and b = 5.70 ft. If the normal stress in each member must not exceed 60 ksi, determine the maximum load Pmax that may be supported by the structure. b B E b
Dron Acompound steel [G=80 GPa) shaft consists of a solid 110-mm-diameter segment (1) and a solid 56-mm-diameter segment (2). The allowable shear stress of the steel is 96 MPa, and the maximum rotation angle at the free end of the compound shaft must be limited to 54°. Determine the magnitude of the largest torque that may be applied at C. (1) 120 (2) 18 Te
ANSWER WITH STEP BY STEP SOLUTION
The bell-crank mechanism is in equilibrium for an applied load of P = 15 kN. Assume that a = 270 mm, b = 205 mm, and 8 = 66°. The pin at B has a diameter of d = 16 mm, and the bell crank has a thickness of t = 6 mm. Calculate the average shear stress in the pin at B. (1) Answer: T= i Bell crank A a B Support bracket MPa B
A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid brass shaft with an allowable shear stress of 51 MPa. Segment (2) is a solid aluminum shaft with an allowable shear stress of 78 MPa. If a torque of Tc = 25700 N-m is applied at C, determine the minimum required diameter of the brass shaft d₁ and the aluminum shaft d2. Tc Answers: d₁ = i √₂ = i (2) с B A mm mm