The beam AC is assured to be rigid andis supported as shown.2. If deflection at free end is 3 mm.What is the tensión in the rod? E = 200GPaa. 35.58 kNc. 54.73 kNb. 68.49 kNd. 41.88 kN3. What is the stress in the roda. 133.33 MPac. 154.73 MPa4. If the stress in the rod is 200 MPa,b. 128.21 MPad. 143.53 MPawhat is the safest load W?a. 41.88 kNc. 54.37 kNb. 39.34 kNd. 48.64 kN]3m@ 20mmo2 m

he beam AC is assured to be rigid and - supported as shown. If deflection at free end is 3 mm. /hat is the tensión in the rod? E = 200 Pa a. 35.58 kN C. 54.73 kN b. 68.49 kN d. 41.88 kN What is the stress in the rod b. 128.21 MPа d. 143.53 MPa а. 133.33 МРа c. 154.73 MPa If the stress in the rod is 200 MPa, hat is the safest load W? a. 41.88 kN c. 54.37 kN b. 39.34 kN d. 48.64 kN ]3m@ 20mmo

he beam AC is assured to be rigid and - supported as shown. If deflection at free end is 3 mm. /hat is the tensión in the rod? E = 200 Pa a. 35.58 kN C. 54.73 kN b. 68.49 kN d. 41.88 kN What is the stress in the rod b. 128.21 MPа d. 143.53 MPa а. 133.33 МРа c. 154.73 MPa If the stress in the rod is 200 MPa, hat is the safest load W? a. 41.88 kN c. 54.37 kN b. 39.34 kN d. 48.64 kN ]3m@ 20mmo

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the deflection 8g at the free end of a cantilever beam AB with a uniform load of intensity q=4 kN/m acting over the middle of the length and a point load. The lenghth of beam is equal to L=3 m. The beam has flexural rigidity El=4286311 Nm². Note that upward deflection is positive. P=qL/6 A +4 3 9 L 3 13 B ↑
Rigid bar ABCD is pinned at C and supported by bars (1) and (2) at A and D, respectively. Bar (1) is aluminum and bar (2) is bronze. A concentrated load P = 80 kN is applied to the rigid bar at B. Compute the normal stress in each bar and the downward deflection of the rigid bar at A.
6–119. Determine the maximum allowable intensity w of the uniform distributed load that can be applied to the beam. Assume w passes through the centroid of the beam's cross-sectional area, and the beam is simply supported at A and B. The allowable bending stress is o allow = 165 MPa. %3D A 15° 6 m w(6 m) 15° 15 mm 100 mm 100 mm 10 mm 15 mm 15° 100 mm Probs. 6–118/119
Determine the value of the uniformly distributed loadd "w". What is the numeric value of C1 ( 1st constant)? Dtermine the deflection at midspan.
3. The rigid bar BDE is supported by two links AB and CD. Link AB is made of steel (E=200 GPa) and has a cross-sectional area of 700 mm'; link CD is made of aluminum (E=70 GPa) and has a cross sectional area of 500 mm. For the 28 kN force shown, deflection at E. A 0.4 m 0.3 m 28 kN D 0.25 m 0.60 m
A rigid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D, as shown. Neglect deflections of the bar due to bending. Use E-200 GPa. How much will rod CD elongate due to the load at B?
Prob 5. Calculate the maximum deflection dmax and the angle of deflection on the supports of a uniformly loaded simple beam loaded as shown. The maximum bending stress is o=60 MPa. The cross section of the beam is square with a length of 8 cm on each side. The beam is made of aluminum having modulus of elasticity E = 70 GPa. q = 2.0 kN/m L= 2.0 m
ASAP NEED COMPLETE SOLUTION !!
The T-beam is subjected to a bending moment of M = 150 kip in. directed as shown. Determine the maximum bending stress in the beam and the orientation of the neutral axis. Make sure you check all possible points (corners) for max stress and/or state other reasoning for the point that you pick. Answer: [σmax = 3.33 ksi, β = -63.1°]
The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 500 mm; link CD is-made of steet E = 200 GPa) and has a cross-sectional area 600 mm. For the 30-kN force shown, determine the deflection (a) of B, (b) of D, (c) of E. 0.4 m 0.3 m 30 kN E T0.4 m 0.2 m
Compute the deformation of the beam using conjugate method E= 200 GPa I= 1000 x 106 mm4
A rigid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D, as shown. Neglect deflections of the bar due to bending. Use E-200 GPa. What is the displacement of the loaded end B of the bar?