Rigid bar ABCD is pinned at C and supported by bars (1) and (2) at A and D, respectively. Bar (1) is aluminum and bar (2) is bronze. A concentrated load P = 80 kN is applied to the rigid bar at B. Compute the normal stress in each bar and the downward deflection of the rigid bar at A.

Rigid bar ABCD is pinned at C and supported by bars (1) and (2) at A and D, respectively. Bar (1) is aluminum and bar (2) is bronze. A concentrated load P = 80 kN is applied to the rigid bar at B. Compute the normal stress in each bar and the downward deflection of the rigid bar at A.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A cantilever beam (member AC) is supported with a column (member CD). Force P is applied to Point B, which is located at the midspan of the beam AC. The column is required to prevent excessive deflection of the beam as shown below. Determine the ratio of internal force in the column (member CD) to the critical buckling load of the column (Pcr). The length for both of the members, L, is 1,650 mm. The applied force, P, is 240 kN. The flexural rigidity for the beam and the column, EI, is 4.0X107 kN·mm2.
The rigid beam shown is supported by a pin at A and two steel rods each of diameter 16 mm. If P = 30 kN, determine the tensile forces PBE & PCF in rods BE and CF, respectively. For steel, E = 200 GPa. F 2.0 m E P = 30 kN 2.5 m D -3 m- -3 m-
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1500 in.“]. For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 150 kip-ft, P = 26 kips, LAB = 6.1 ft, LBC = 9.2 ft. MA A LAB LBC
help find the stress at segment BC, please
Q 3. A rigid beam AB is 5.5 m long, hinged at point A and supported by two pipes at C and D as shown in figure 3 below. Pipe 1 at C is of copper has a outer diameter of 120 mm and inner diameter of 100 mm and yield stress of copper is 138 N/mm² Pipe 2 at D is of steel has a outer diameter of 100 mm and inner diameter of 90 mm and yield stress of steel is 250 N/mm2 Calculate the safe load at A if the load factor is 1.66 Pipe 1 Pipe 2 Psafe 2.3 m 2 m C 5.5 m Angle ACE = 0 Figure 3 Angle BDF = 42° Take 0 = 10 Page 7 of 7 PTO
answer with fbd please
H.W. 1:An axial member consisting of two polymer bars is sup- ported at C, as shown in Figure area ol 540 mm and an elastic modulus of 28 GPa. Bar (2) has a cross-sectional area of 880 mm2 and an elastic modulus of 16.5 GPa. Determine the deflection of point A relative to support C. . Bar (1) has a cross-sectional 50 kN Om She 35 kN (1) (2) 50 kN 0.85 m 1.15 m FIGURE
A beam is subjected to a linearly distributed downward load and rests on two wide supports BC and DE, that exert uniformly distributed upward loads as shown. Determine the values of wec and WDE corresponding to equilibrium when WA = 750 N/m. 1200 N/m 20 C WBC ADA A 0.6 m- B' 0.8 m The value of WDE is The value of wBc is [ -3.1 ms -6 m- N/m. N/m. D (DE 1.0m E F
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1620 in.4]. For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 190 kip-ft, P = 26 kips, LAB = 3.6 ft, LBC = 5.4 ft. %3D %3D P V. MA C LAB LBC Answer: (a) VA = in. (b) VB = in.
Beam AB is supported as shown in the figure. Tie rod (1) is attached at B and C with double shear pin connections, while the pin at A is attached with a single shear connection. The pins at A, B, and C each have an ultimate shear strength of 57 ksi, and tie rod (1) has a yield strength of 33 ksi. A concentrated load of P = 14 kips is applied to the beam as shown. A factor of safety of 2.4 is required for all components. Determine: (a) the minimum required diameter for tie rod (1). (b) the minimum required diameter for the double shear pins at B and C. (c) the minimum required diameter for the single shear pin at A. 6.7 8 in. 3.8ft (2) 8.5ft
can sameone solve this thanks.
Determine the largest weight “W” that can be supported by the two wires AB and AC. The working stresses are 100MPa for AB and 150MPa for AC. The cross sectional area of AB and AC are 400mm2 and 200mm2.