The shaft in the figure has a hollow part from B to A and is solid throughout C to B. The hollow segment is 8mm thick and the shaft has an outer diameter of 80mm. Determine the maximum shear stress developed in the shaft. If B is the midpoint of the 2-meter shaft, and G = 75 Gpa, determine the angle of twist of A with respect to C. PROBLEM 1 B 4 kN-m 2 kN-m

The shaft in the figure has a hollow part from B to A and is solid throughout C to B. The hollow segment is 8mm thick and the shaft has an outer diameter of 80mm. Determine the maximum shear stress developed in the shaft. If B is the midpoint of the 2-meter shaft, and G = 75 Gpa, determine the angle of twist of A with respect to C. PROBLEM 1 B 4 kN-m 2 kN-m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The steel tube seen below has an outer diameter do = 60mm and an inner diameter d, = 50mm. It is subjected simultaneously to torque T = 1.5kN-m and to axial load P = 205kN. Determine: (a) the maximum in-plane shear stress and its orientation, (b) the associated normal stress and (c) sketch both on a properly oriented element.
The segment AB of the steel torsion bar is a cylindrical tube of constant 2-mm wall thickness. Segment BC is a square tube with a constant wall thickness of 3 mm. The outer dimensions of the cross-sections are shown in the figure. The tubes are attached to a rigid bracket at B, which is loaded by a couple formed by the forces P = 17 kN. Determine the maximum shear stress in the shaft. Take G = 75 GPa. P 1.2m C 100 mm 100 mm t = 3 mm 1.2m 80 mm B 300 mm A -t = 2 mm Important reminder: The formulas derived for thin-walled tubes are just approximations. So, for the case of hollow circular tubes with constant thickness, you should still use Tc/J and TL/JG to solve for the shear stress and angle of twist, respectively.
A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the left by u = 2.4 mm and upward by v = 5.8 mm to new position Q′. Determine the shear strain γ at corner Q′ after deformation. Use c = 730 mm, α = 25°, and β = 65°.
From the previous problem, determine the shear stress 30 mmabove the neutral axis.
A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the left by u = 1.3 mm and upward by v = 5.2 mm to new position Q'. Determine the shear strain y at corner Q'after deformation. Use c= 665 mm, a = 23°, and B = 67°. P R Answer: Y = i prad
Figure Q2 shows a statically determinate plane truss subjected to a horizontal concentrated load at B. The truss is made using steel with Young’s modulus of 205 GPa, and the cross section area for all members are constant. If the horizontal displacement at B is limited to 10 mm, determine the minimum cross section area required for the truss. The solution can be based on Method of Conservation Energy or Method of Virtual Work.
A compound shaft ABC (composed of two parts AB and BC) is subjected to a torque-load shown in the Figure. Support A allows angular-twist not to exceed 0.5 degree, while support C is rigid. Given that part AB has solid circular section (r= 15 cm), while part BC has tubular circular section (r= 15 cm; t = 2 cm), and for given geometry: a) Determine the maximum shear stress in the shaft. b) Determine the angle of twist on. c) Determine the relative angle of twist o G-70 GPa # * 2m 450 kN.m B
Use Mohr's circle to determine the principal stresses and the normal and shear force along plane AB.
Rhelp**
If M, = 285 kip-ft, find the magnitude of the bending stress at a point H For the beam cross section, assume a = 9 in. b= 12 in. d= 31 in r= 45 in. The centroid of the cross section is located 14.16 in. below the uppermost surface of the beam. The moment of inertia about the z axis is 26227 in 4
A circular shaft which has a diameter of 100 mm is subjected to torque of 5 kN-m. The shear stress in N/mm2, induced in the shaft would be A B D 160 TT 120 π 125 π 80 E TT
Solve it