The T-section in the figure was created by gluing two rectangular wooden planks of 18 cm in size with glue. Since the glue value of the shear force affecting the section is Ty = 10kN, determine what the minimum safety stress of the glue should be in order to ensure joint security. (Ix = 11016 cm ^ 4) Write the result after the comma, rounding it to two decimal places and specifying. 18cm T. T. 6cm tutkal 18cm Y15cm 6cm

The T-section in the figure was created by gluing two rectangular wooden planks of 18 cm in size with glue. Since the glue value of the shear force affecting the section is Ty = 10kN, determine what the minimum safety stress of the glue should be in order to ensure joint security. (Ix = 11016 cm ^ 4) Write the result after the comma, rounding it to two decimal places and specifying. 18cm T. T. 6cm tutkal 18cm Y15cm 6cm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

USE IMAGE BELOW And Give your answer in in^4
Solve correctly without doing mistake.
Show your complete solution and make sure that your finals answer is in 4 decimal places, please make it readable.
I need help please
An aluminum [E-9600 ksi] control rod with a circular cross section must not stretch more than 0.34 in. when the tension in the rod is 2070 lb. If the maximum allowable normal stress in the rod is 12.9 ksi, determine: (a) the smallest diameter d that can be used for the rod. (b) the corresponding maximum length L of the rod. Answers: (a) d- i in. (b) L- in.
5
Joints B and D use a pin with a diameter of ø10 mm. In connection C, the diameter of the pin is ø6 mm. The permissible shear stress τmax of the pins is 75 MPa and the permissible normal stress σmax of the rod BD is 200 MPa. Determine the maximum allowable value of the force P. Units [N, mm] Enter the answer to one decimal place. Do not round the invoices in the intermediate stages, but only the final answer! Dimension L = 300 mm
A (160+Reg. No.) kN force is applied as shown at the end of a hot-rolled steel beam. Neglecting the effect of fillets and of stress concentrations, perform calculations in MS excel or MATLAB for the principal stresses in the beam to satisfy a design specification that they be equal to or less than 150 MPa. If the principal stresses are more than the given value, what would you change in the beam so that satisfy the required stresses. 210 mm 13 mm a 1035 mm 110 mm 160kN +Reg No. 0.4m (b) (a) Figure: Hot-rolled cantilever steel beam a) 3D view of the beam b) Cross-section of the beam
1.4 (A). Twe fork-end pieces are to be joined together by a single steel pin of 25 mm diameter and they are required to transmit 50 kN. Determine the minimum cross-sectional area of material required in one branch of either fork if the stress in the fork material is not to exceed 180 MN/m2. What wili be the maximum shear stress in the pin' [1.39 x 10-m'; 50.9 MN/m] 1.5 (A) A simple turabuckle arrangement is constructed from a 40 mm outside diameter tube threaded internally at each end to take two rods of 25 man outside diameteT with threaded cnds. What will be the nominal stresscs set up in the tube and the rods, ignoring thread depth, when the turabuckle carries an axial load of 30 kN? Assuming a suficient strength of thread, what maximum load can be transmitted by the turnbuckle if the maximum stress is imited to 180 MN/m? [39.2, 61.1 MN/m2, 88.4 kN.]
The force F exerted by the hand on the handle in the figure is 22 N. Calculate the compression force on member BE.Type the units in the numeric entry using a space between the units and the number. The use of capital letters is required.
- Once answered correctly will UPVOTE!!
The force F exerted by the hand on the handle in the figure is 54 N. Calculate the compression force on member BE.Type the units in the numeric entry using a space between the units and the number. The use of capital letters is required.