Determine the smallest allowable cross-sectional areas of each me 400 kN The working stresses are 60 MPa in tension and 45 MPa in compression. 3 m 500 kN B 2 m 50° m

Q: 3.) In In an actual Rankine cycle, steam first enters the turbine at 10 MPa and 400C. It expands to…

A:

Q: A motor supplies a constant torque M = 6 kN · m to the winding drum that operates the elevator. The…

A:

Q: For the problem shown below, you are given x1 = 0.28 m, x2 = 0.05 m, x3 = 0.18 m, and y1 = 0.07 and…

A:

Q: S6.2 Helium expands polytropically through a turbine at pV1.5 = C. Inlet is at 1000K and 1000 kPa.…

A:

Q: a) If a pipe with an inner diameter of 36 mm is subjected to an axial load of 5.20 x 105 N and the…

A: a) Given: Inner diameter=36mm or 0.036mAxial load (F)=5.2×105NMaximum allowable stress…

Q: A 10 cm diameter solid aluminum post is subjected to a horizontal force of V= 7.1 kN and a…

A:

Q: A small gold balls, whose diameters are 5 mm, are heated in the oven to 600 °C. After heating…

A: To obtain the solution to the above question we will use two concepts- 1. Concept of lumped…

Q: Initially, a rigid tank contains 500L of water at 300°C. By volume, the tank contains60% liquid and…

A:

Q: What is the magnitude of the force on an inclined gate shown? The tank contains water and is…

A:

Q: Prob. From the given Fiqure. 150 KN 90° 180 KN 2m A im Reg'd u) vertical reaction at the hinge (2)…

A:

Q: 2. Assume that axial deformation of Member EF is caused mainly by its reaction to external forces on…

A:

Q: Question 1 The helical steel extension spring has a diameter of 2 inch, wire diameter of 0.1 inch,…

A: Given: diameter of the spring: D=2 inch diameter of the wire: d=0.1 inch for steel shear modulus:…

Q: The answer for one should be 8.572 but I don’t know how to get that answer. Please show me all your…

A: Solution:

Q: The following figure depicts a 1600 rpm motor, gear box, and 4000 rpm blower. The gear box weighs 40…

A: “Since you have posted a question with multiple sub-parts, we will provide the solution only to the…

Q: A chemistry graduate student is designing a pressure vessel for an experiment. The vessel will…

A:

Q: Figure 1 shows an element ith stresses. Angle 1 Tyx Tyx Figure 1 Point C)- x-direction stress…

A: The three basic equations to determine the stress at various cross-sections are:…

Q: Figure P2.26 shows an exploded view of an airplane engine, reduction gear, and propeller. The engine…

A: The torque of an engine is given by,

Q: Show your steps and label units on all answers. 1.) Determine the Forces in all the members, and the…

A:

Q: solve for the direction and put a conclusion after getting the answer. Make sure that the answers

A: Resultant load is equal to the area under the curve Resultant load pass through CG of load

Q: Why when plugging the formula for crossectional it gives a different value than 6650m2. The table…

A:

Q: The coefficient of friction everywhere is 0.30. If max force P at static equilibrium is 55N, find…

A: Solution: Considering the weight acts at the midpoint of the ladder, then Considering static…

Q: For the connection shown, the bolt diameter is d = 20 mm. The average shear stress in the bolts must…

A:

Q: Thank you for your help. I was able to get them all but can't get F correct. Could you help me with…

A:

Q: kindly help me with this one. Write your answer with four decimal places and enclose them in a box.…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: for Part V) should the answer not be -0.4 to the final part of the question since the number put…

A: We have, general equation of the system as x=4.23sin100πt-1.79cos100πt We can write it in the…

Q: The steel wide-flange beam has the dimensions shown. If it is made of an elastic perfectly plastic…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked .…

Q: A fire tube boiler develops 75 metric tons of steam at a pressure of 12.5 mpa and a temperature of…

A:

Q: O lit/sec water enters a centr ally at 5 m/s and leaves at a - axial direction. If the inlet

A:

Q: 1-54)  Figure P1-54 shows the shape of a test specimen used to measure the tensile properties of…

A: given data as per question initial diameter of bar = 3/8*2  = 0.75in final diameter in the middle of…

Q: When using the flexure formula, Mmar C (9492.188×10' )Nmm (;) 30N/mm2= at 12 a=123. 822mm

A: Given Data :

Q: Problem 3. Problem. The upper beam in figure is supported by a reaction R3 at D and a roller at C…

A:

Q: A 0.75-m x 1.5-m window is constructed of 6-mm-thick glass. On a cold night, the inside and outside…

A: “Since you have posted multiple questions with multiple sub parts, we will provide the solution only…

Q: For each question, provide an explanation, identifying the correct choice ( it is marked in red)…

A:

Q: Reaction value at support A. Positive direction is considered upwards. Enter your answer in kN to 2…

A:

Q: A Carnot heat engine receives heat at 700 K and rejects the waste heat to the surroundings at 300 K.…

A:

Q: In a three-phase separator, gas, oil, and water are separated into layers of different depths. The…

A:

Q: K A weight of 1300 pounds is suspended from two cables as shown in the figure. What is the tension…

A: Weight=1300poundAngle A=40 degree           B=30 degreeDetermine the tension of cable

Q: Please can you show the shear force diagrams for the questions 1 to 4

A:

Q: To find the Mechanical Advantage of ANY simple machine when given the force, use MA = R/E. An Effort…

A: Write the value of load.   R=90 N   Write the value of effort.   E=30 N

Q: The machine shown is used for moving heavy items such as pallets of bricks around construction…

A:

Q: )The principal stresses.b)The principal directions (angles to the principal planes).c)The maximum…

A: Given:

Q: The students will pass at the end of the semester as part of compilation requirement. Problem 1.…

A: