Q-The lap distance in different types of bonding is equal to the horizontal distance between two Perpend joint in the rows sequential and must be equal to half the width of the brick minus half width of the Perpend joint and the value was . and it ..... .... must be applied to prevent the continues of perpend joints in the sequential rows. five point five cm (5.50 cm) five point seven five cm (5.75 cm) Non of them five only (5.00 cm) O five point two five cm (5.05 cm)

Q-The lap distance in different types of bonding is equal to the horizontal distance between two Perpend joint in the rows sequential and must be equal to half the width of the brick minus half width of the Perpend joint and the value was . and it ..... .... must be applied to prevent the continues of perpend joints in the sequential rows. five point five cm (5.50 cm) five point seven five cm (5.75 cm) Non of them five only (5.00 cm) O five point two five cm (5.05 cm)

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter7: Tubing And Piping

Section: Chapter Questions

Problem 14RQ: When soldering, a flux is used to A. minimize oxidation while the joint is being heated. B. allow...

See similar textbooks

Similar questions

i need the answer quickly
4. Design a welded connection to resist the loading shown below (service load). A double angle tension member, 2 L5x5x5/16, is connected to a 3/8 inch thick gusset plate with fillet welding. Fy = 50 ksi for the angles and Fy = 36 ksi for the gusset plate. Compute the size and length of welding on the side of angles based on LRFD and indicate the information on the sketch. 1 = %" 2L5 x 5 x h6 D = 30 k L= 75 k
1) A single parallel fillet weld of total length L and weld size h subjected to a tensile load P, will have what design stress? O Tensile and equal to P/0.707LH O Tensile and equal to P/Lh Shear and equal to P/0.707Lh Shear and equal to P/Lh
Note: All dimensions are in mm E - 210 000 MPa (N/mm') F-13 IN 1. A bracket is shown in the figure. Calculate the stresses on the welding. The bracket welded by E7018 clectrode. Based on stresses calculations, calculate the design factor of safety ELECTRODE TENSILE NUMBER YIELD STRENGTH STRENGTH _(MPa) (345) (393) (462) (531) (MPa) E60xx (427) (482) (551) (620) A = 0.707h(b + 2d). E70xx i = b/2 ESOxx b+ 2d E90xx 2d3 (600) (737) - 2d?y + (b+2d)3² 3 E100xx (689) (827) %3D E120xx
A Draw sectional front view only of a double riveted zigzag lap joint to join two plates of thickness t-10mm (All dimensions must be calculated on a side and marked on the drawing)
Нome work 1. A plate( 100 mm) wide and (10 mm) thick is to be welded with another plate by means of double transverse welds at the ends. If the plates are subjected to a load of (70 kN ), find the size of weld for static as well as fatigue load. The permissible tensile stress should not exceed (70 MPa) [Ans. 83.2 mm; 118.5 mm]
A steel bridge rail is 400 meters long. During winter, the temperature dropsto -40 C and goes back to 40 C during summer. What should be the specifiedallowance between the mating parts? Coefficient of expansion for steel is 11.7x 10 -6 mm/mm –C.
Label all links starting with "1" and all joints starting with "A". Include whether the joint is a half joint or full joint as well as the type of joint.
Sketch a V-grooved butt joint, and label all of the joint's dimensions.
Moving to another question will save this response. Quèstion 11 The type of joint used in wooden photo frarnes is O A. Mitre joint O B. Cross lap joint O C. Double Mortise and Tenon joint OD Blind Mortise and Tenon joint A Moving to another question will save this response. Windows bul alacl Jal ENG 4) T-T/E//V
Dynamic forces F1 = 4000N and F2 = 6000N are applied to the welded part shown in the figure as shown below. For dynamic forces, both dynamics are synchronized, and when the force in the y-axis direction is downward, it is on the right in the x-axis direction. When the force is up, the other force is on the left. The welded part is made of 1018 HR steel, 10 mm thick. a) Safety factor for welding? b) Calculate the safety factor for the base metal. (Electrode type for question is E9010.)
The following figure shows the connecting part of a suspension assembly. Impact on the part What is the seam length of the weld joint if the magnitude and direction of the force F acting on it is constant? should be. Material St37 and welding quality II will be take F=10 kN, s=10 mm, sa F L