need to find force at each joint from this cable and figure out what yb is? The image presents a structural mechanics problem involving a beam supported at two points. It includes loads and specific distances measured in feet.### Description:- **Supports:** - Point A and Point D are fixed supports indicated by small triangles set on top of a horizontal line.- **Applied Loads:** - There is a downward force of 7 kips (7k) at Point B. - A downward force of 12 kips (12k) is applied at Point C.- **Distances:** - The beam is divided into three segments along the top: - The segment from A to B is 2 feet. - The segment from B to C is 7 feet. - The segment from C to D is 3 feet.- **Vertical Dimensions:** - An explicit vertical dimension of 5 feet is marked from a line parallel to the beam above Point C. - There is also a labeled vertical component \(V_B\) at Point B.### Diagram Indications:- This is a line diagram, typically used in engineering to analyze forces in beams.- The different segments and loads help to calculate reactions at the supports and other forces in the system.This setup is likely part of an exercise in statics or structural engineering, meant to teach students how to resolve forces and analyze supported beams under various load conditions.

Answered: Image /qna-images/answer/b00d0730-eca2-4c46-834f-f34a1f36a253.jpg

Answered: need to find force at each joint from…

Engineering

Mechanical Engineering

need to find force at each joint from this cable and figure out what yb is?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: If the number of members in a truss frame is more than (2J - 3), the truss is called a redundant…

Q: msIf we apply a compressive load to a perfectly straight steel rod that is circular in cross section…

A: Draw the schematic diagram of the circular column which is pinned at both ends and is loaded by a…

Q: 1. A 10 mm steel plate is welded on a wider steel plate as shown. The weld leg, w = 12 mm. Find the…

Q: Preliminary truss analysis assumes that loads are applied to the truss at pinned joints only. True…

A: Given data To identify the given statement is True or False.

Q: If I had one singular hinge joint, which total different direction could it provide a force in?

A: The hinge joint can rotate and proves zero restriction about the hinge point, thus moment reaction…

Q: 0 W12X31 6-120 1.10m 4.20m 3.2n

Q: МЕТНОD ОF JONT DETERMINE THE FORCE IN MEMBERS of the shown in figure 18kn 18kn 18kn 18kn 18kn 18ko…

Q: swer the following: 1) Define the degree of freedom of a joint? 2) How many degrees of freedom does…

A: To define: 1) Define the degree of freedom of a joint?2) How many degrees of freedom does a c-joint…

Q: Calculate the degree of freedom, point out the positions if there are multiple joints, high-pair and…

Q: Two 1/4 in × 8 in A36 steel plates are joined with a lap joint using 3/4 in A325-N bolts. If a…

A: Steel plates of size 14 in × 8 in of A 36 steel Ultimate tensile strength of A 36 steel is…

Q: Determine the force in each member of the truss and state if the members are in tension or…

A: Answer: FAI 4.039 kip (Compressive) FAB 3.750 kip (Tensile) FBI 0 FBC 3.750 kip (Tensile)…

Q: (d) Calculate the mobility using the Kutzbach revision of Gruebler equation. 2

A: Find the mobility

Q: The figure shows a welded-arm. The arm is welded using ! normal yield strength of 393MPa. If the…

A: Given data: The given weld size from the figure is The radius of the weld is

Q: Pre-tensioning of a bolted joint is used to (a) strain harden the bolt head (b) decrease stiffness

A: Given: Pre-tensioning: When nut is tighten against the bolt, a compressive force is induced in…

Q: For the "C" shaped welded joint shown, the magnitude of force P that will result in a moment of 1540…

Q: e the directions of reactions in the joints in the statec, please explain to me

A: The direction of the forces and moments acting on the connected objects must be an allowable…

Q: explain how the moment diagram get especially in 50 to 250kN-m

A: Given: Explain how the moment diagram get especially in 50 to 250kN-m

Q: Use LRFD and design a welded connection to resist the available strength of the tension member in…

A: Drawing the plate with the dimensions ,

Q: Determine the magnitude of the load on the worst loaded rivet

A: Given: A horizontal plate has been joined to a vertical post using four rivets as shown in figure:…

Q: 1. A 10 mm steel plate is welded on a wider steel plate as shown. The weld leg, w = 12 mm. Find the…

Q: 1. Calculate the forces in all members of the truss shown using the method of joints. 5,000 lb 1,000…

Q: Q3 (a) What are the methods used to obtain a good weld when welding steel when the carbon content is…

A: Force ,F=60000 lbAllowable stress,Size of the weld ,h=1/4 inchTo determine:a)the method used to…

Q: True or False: Frictionless 2D Pins and 2D Hinges have reactions in both the x and y directions.…

Q: one

A: Answer :- False

Q: QUESTION 2. Determine the reaction at pins at A, B and C and fixed joints. Answer in component form.…

Q: 1. Using the method of joints (no other method is acceptable), determine the reactions and the force…

A: GIVEN DATA- A PLANE TRUSS GIVEN WE HAVE TO FIND FORCES IN MEMBER

Q: If the number of members in a truss frame is less than (2J - 3), the truss is called a deficient…

A: true is the answer as per the above given condition

Q: Calculate the muscle mechanical advantage: GRF = 2400 N GRF moment arm = 80 cm Muscle moment arm =…

Q: 「十 a-6

A: Given:

Q: What is the internal moment in the column?

A: Internal moment: It is the moment equal in magnitude and opposite in the direction to sum of all…

Q: Please use method of joints to find the forces in members AB, AC, BC, BD, CD, and CE!!! Thank you!

Q: For the following joint as shown in Figure 6, write the number of prismatic joints and revolute…

Q: To make truss stable how many member are required Support reaction=4 Joint=7

A: Given:- Support reaction = R = 4 Joints = J = 7 members = M = ?

Q: D he' E method of joints 30° 10¹ c Show Transcribed Text 1000# F 1000#

Q: Yivt(d) Hiw@. what alead (F) مهمل required to sperate the riveted plates shocun in frigure? & =(80…

Q: FIND THE FORCES IN JOINT A

Q: Determine the required fillet welds to support pulley on the shaft to carry applied loads shown in…

A: Given: The power, P = 120 HP = 120 x 0.745 = 89.4 kW The speed, N = 75 rpm The diameter, d = 4 in…

Q: What is the Maximum/minimum point on the curve of Moment Diagram.

A: Moment diagram is the diagram obtained by using bending moment at each point of structure.

Q: 18 kN 3 B 25 kN 8m DE 6m D 10 kN Figure 1

Q: 1. Via the METHOD OF SECTIONS, determine the loads as well as the kind of loads in the members BD,…

A: Find the force in BD, BE and EF

Q: Q3 (a) What are the methods used to obtain a good weld when welding steel when the carbon content is…

A: Force ,F=60000 lbAllowable stress,Size of the weld ,h=1/4 inchTo determine:a)the method used to…

Q: Q1: The weldment shown in the figure is subjected to a force F. The hot-rolled steel bar has a…

A: we have to evaluate the value of F

Concept explainers

Basic Terminology in Mechanics

The area of science and mathematics concerned the motion of the objects, the relation between the force matter, and motion if specified. Forces exerted over the objects result in displacements or changes in the position of an object concerning its environment. This branch of physics keeps its roots in Ancient Greece in the form of the scripts of Aristotle and Archimedes.

Question

need to find force at each joint from this cable and figure out what yb is?

The image presents a structural mechanics problem involving a beam supported at two points. It includes loads and specific distances measured in feet.

### Description:

- **Supports:**
- Point A and Point D are fixed supports indicated by small triangles set on top of a horizontal line.
- **Applied Loads:**
- There is a downward force of 7 kips (7k) at Point B.
- A downward force of 12 kips (12k) is applied at Point C.
- **Distances:**
- The beam is divided into three segments along the top:
- The segment from A to B is 2 feet.
- The segment from B to C is 7 feet.
- The segment from C to D is 3 feet.
- **Vertical Dimensions:**
- An explicit vertical dimension of 5 feet is marked from a line parallel to the beam above Point C.
- There is also a labeled vertical component \(V_B\) at Point B.

### Diagram Indications:

- This is a line diagram, typically used in engineering to analyze forces in beams.
- The different segments and loads help to calculate reactions at the supports and other forces in the system.

This setup is likely part of an exercise in statics or structural engineering, meant to teach students how to resolve forces and analyze supported beams under various load conditions.

Expert Solution

Step 1: Draw the given diagram.

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The answer is one of the options below please solve carefully and circle the correct option Please write clear .
Show the process on how to get the answer. Include free body diagram.
The fabricated steel members are being assembled into a truss on-site in the municipality of Alfonso, Cavite. The assembly started at the elevated ground at both sides and is to meet at the midspan. Nearing to the end of construction, it was found that the last member, CD, was fabricated too short by A D= 4.450 mm. The engineer then came up with an idea of applying a force P at joints C and D as shown to close the gap. P. с c' P 3 m -3 m- -3 m- 3 m- Use E = 200 GPa and cross-sectional area of members BC, DE, CD each 4500 mm2 while AC and DF being 6363.961 mm2 a) Determine the necessary force, P, to close the gap in kN. wwww b) If force P will then be removed after being assembled, calculate the force in CD in kN.
Determine the force in each member of the loaded truss. All triangles are 3-4-5. Enter a positive number if the member is in tension, negative if in compression. Part 1 19 KN BI 8 H Correct We can also see that BI = DI G -4 panels at 8 m Answer: Cl = 0 21kN I 40 KN Consider joint I. The Free-Body diagram is shown. All members are assumed to be in tension. Use this diagram to find the force in Cl. Use a positive number if in tension, a negative number if in compression. CI KN F D E DI
5
Calculate the outer moment T12 and the joint forces F34, F32, G14, G12, F43, F23.
Convert the distributed load in figure to concentratedload and determine the reactions.
Find degree of freedom for folding ironing board showed in picture.
B5
Find out degree of freedom ?number of link ,joint, must be indicted like as link symbol L and Joint symbol j.
To make truss stable how many member are required Support reaction=4 Joint=7
Solve (e) part only in one hour only plz Plz solve right now its mechanical engineering question plz don't reject and do it now