The solid 32 mm diameter steel [E - 200 GPa] shaft supports two belt pulleys. Assume that the bearing at B can be idealized as a rollersupport and that the bearing at D can be idealized as a pin support. For the loading shown, determine:(a) the shaft deflection at pulley A.(b) the shaft deflection at pulley C.Assume P- 500 N, Q- 950 N, Las - 450 mm, Lạc - 650 mm, Lco - 650 mm.ABCDLABLBCLCDPart 1Calculate the area moment of inertia for the solid circular cross-section.Answer:|- imm4

Given, A solid circular shaft, Diameter= D = 32mm P = 500N Q= 950N Modulus of elasticity = E =…

The solid 32 mm diameter steel [E- 200 GPa] shaft supports two belt pulleys. Assume that the bearing at B can be idealized as a roller support and that the bearing at D can be idealized as a pin support. For the loading shown, determine: (2) the shaft deflection at pulley A. (b) the shaft deflection at pulley C. Assume P- 500 N, Q - 950 N, Las - 450 mm, Lsc- 650 mm, Lco - 650 mm. B C LAB LBC LCD Part 1 Calculate the area moment of inertia for the solid circular cross-section. Answer: |- i mm

The solid 32 mm diameter steel [E- 200 GPa] shaft supports two belt pulleys. Assume that the bearing at B can be idealized as a roller support and that the bearing at D can be idealized as a pin support. For the loading shown, determine: (2) the shaft deflection at pulley A. (b) the shaft deflection at pulley C. Assume P- 500 N, Q - 950 N, Las - 450 mm, Lsc- 650 mm, Lco - 650 mm. B C LAB LBC LCD Part 1 Calculate the area moment of inertia for the solid circular cross-section. Answer: |- i mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

E 10-59. The A-36 hollow steel shaft is 2 m long and has an outer diameter of 40 mm. When it is rotating at 80 rad/s, it transmits 32 kW of power from the engine E to the generator G. Determine the smallest thickness of the shaft if the allowable shear stress is 7allow = 140 MPa and the shaft is restricted not to twist more than 0.05 rad.
Solid mech.shaft.
At what distance a should the bearing supports at A and B be placed so that the deflection at thecenter of the shaft is equal to the deflection at its ends? Use MAM. The bearings exert only on theshafts. The flexural rigidity is constant.
Group - C- Design a simply supported rectangular reinforced concrete beam. Note: The self-weight of the beam is included. Wa u (D.L) 90 KN/M Wu (L.L) 70 KN/M 700mm 330 mm 7m- FY Mpa=350 Fc MPA= 21 No.oflayers=two Bar die =20
2. The crank mechanism shown below is in equilibrium. Determine: a) the diameter of cylindrical connecting rod CD, given that normal stress is limited to 120MPa; b) the shear stress in the pin at B, where the pin has diameter of 8mm; and c) the bearing stress in the bracket supports at B. C 120° A 8kN 300mm B 30⁰ D P 200mm 6mm B 15mm 6mm 8mm Detail of pin and pin brackets
4) will upvote anyone who will answer
a. Draw the FBD b. Determine the value of P c. Determine the bearing reaction at A. D P. RA E 60° 25" C Az 14" 210 lbs -- - 20
The bracket shown carries an eccentric load P at an eccentricity e=400mm. The column and bracket are A36 steel. Diameter of bolt is 22mm in standard holes. Assume that the column flange and the bracket are thick enough that single shear in the bolts will control. Shear capacity of one bolt is 45KN. a. Determine the polar moment of Inertia of the bolt group b. Determine the maximum load P that the bolted connection can support. C. Determine the direct load carried by the most critical bolt d. Determine the load due to moment carried by the most critical bolt. e = 400 mm 75 751 15 75 75 70 70
1
Please limit your answers to four decimal places and should be expressed without constants.
Q6b .solve this.
"1-80. Determine the maximum allowable torque T that can be transmitted by the joint. The shear pin A has a diameter of 25 mm, and it is made from a material having a failure shear stress of Tai 150 MPa. Apply a factor of safety of 3 against failure. 100 mm