The gear-pulling assembly shown consists of a crosshead CF, two grip arms ABC and FGH, two links BD and EG, and a threaded center rod JK. Knowing that the center rod JK must exert a 4800-N force on the vertical shaft KL in order to start the removal of the gear, determine all forces acting on grip arm ABC. Assume that the rounded ends of the crosshead are smooth and exert horizontal forces only on the grip arms. 80 mm 60 mm 80 mm E 150 mm B 250 mm K A |H 95 mm Fig. P6.144

The gear-pulling assembly shown consists of a crosshead CF, two grip arms ABC and FGH, two links BD and EG, and a threaded center rod JK. Knowing that the center rod JK must exert a 4800-N force on the vertical shaft KL in order to start the removal of the gear, determine all forces acting on grip arm ABC. Assume that the rounded ends of the crosshead are smooth and exert horizontal forces only on the grip arms. 80 mm 60 mm 80 mm E 150 mm B 250 mm K A |H 95 mm Fig. P6.144

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: B 1 A 1/2 IP 1/2 IP 1/2 D A frame ABCD is supported by a roller at A and is on hinge at C as shown…

Q: nt B of each force Olb F3 = 160 lb 4-5. Determine the moment of each of the three forces about point…

Q: Refer to the Column Interaction Given: F’c = 27.5 Mpa Fy = 414 Column diameter 400mm Main bar…

A: Step 1: Refer to the interaction Diagram so you can find the pg. and use the formula for the Area…

Q: 3. Determine the support reactions on the member shown below. The collar at B is fixed to the member…

A: Given, external force of 100 lb To determine, support reactions

Q: *4-12 The truss is made of three A-36 steel members, each having a cross-sectional area of 400 mm².…

A: Sc= 0.0975 mmExplanation:

Q: The bell crank as shown in the fig. is in equilibrium, determine the shearing force in the pin at D.…

A: To find shear force at D

Q: The compound beam is fixed at A and supported by a rocker At B and C. There are hinges (pins) at D…

Q: Im 0.5 m 0.5 m 0.5 m B D 1 m- 0.5 m E

A: carrier system is givensupported at A and CG=2KNFindthe vertical support reactions and the rod…

Q: (Mc)y = -226 N-m The shaft is supported at its ends by two bearings A and B and is subjected to the…

Q: Q5 Draw the influence line for (a) the moment at B, (b) the shear at C, and (c) the vertical…

A: A beam with vertical roller support at A such that it resists only moment and horizontal force and a…

Q: Draw the ILD diagram for the member DG and determine the maximum force developed in member DG of the…

A: To construct ILD for member GD, apply unit load load at every junction and calculate the load…

Q: P9-1 D The steel rod (E= 200GPA) is subjected to the loading shown. If the cross-sectional area of…

Q: 1-7. Determine the resultant internal loading on the cross section through point D of the pliers.…

Q: In the assembly shown. the block has a weight W =200 lbs and the cord is attached to the pin at B.…

A: To find reaction at link AB

Concept explainers

Electric Circuit and Components

An electrical circuit or electrical network is a pre-determined pathway to make the electrons flow in the desired direction. The flow of electrons will set up a current flow in the circuit. Normally, the flow of electrical current is opposite to the flow of electrons. An electron is a fundamental sub-atomic particle of an atom possessing a negative charge. To initiate the flow of current and achieve the desired output, the electrical circuit should necessarily be composed of closed pathways. The pathways are made-up of good conductors of electricity such as aluminium and copper.

Question

The gear-pulling assembly shown consists of a crosshead CF, two grip arms ABC and FGH, two links BD and
EG, and a threaded center rod JK. Knowing that the center rod JK must exert a 4800-N force on the vertical shaft
KL in order to start the removal of the gear, determine all forces acting on grip arm ABC. Assume that the
rounded ends of the crosshead are smooth and exert horizontal forces only on the grip arms.
80 mm 60 mm 80 mm
E
150 mm
B
250 mm
K
A
|H
95 mm
Flg. P6.144

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Calculate the pin reactions at pins A, B, and D in the frame shown. Neglect the weights of the members. - Draw Free-body diagram - Solve quickest most simple way, save yourself time.
The rigid element BCD is supported by a bar AB with a diameter of 25 mm and a connection at C with a diameter of 10 mm. Determine:a. The normal stress in bar AB. b. The shear stress of the bolt at C.
Q-1 Link-2, shown in the figure, is 30 mm wide, has 12 mm diameter bearings atthe ends, and is cut from low carbon steel bar having a minimum yield strength of190 MPa. The end-condition constants for link-2 are C = 1 and C = 1.2 for bucklingin and out of the drawing, respectively.a) Draw necessary and clear free-body diagrams to determine the reactions atthe supports and the load on both member-2 and member-3. b) Determine a suitable thickness for link-2, based on a design factor of safetyηD = 4, and considering a material having E = 207 GPa, and a minimum yieldstrength Sy = 350 MPa.c) Determine the stress and resulting factor of safety for each pin, and state yoursuggestions in case of design factors less than 4.
The assembly consists of two A-36 steel rods and a rigid bar BD. Each rod has a diameter of 0.753 in. If a force of 15 kip is applied to the bar, determine the angle of tilt of the bar in degrees. 3.5 ft 2.5 ft E D -1.25 ft- 0.75 ft' 1 ft 15 kips
Note:hand written solution should ne avoided.
The bar is snugly fit between points C and A before the loading is applied at Collar B. Assume E = 200 GPa for the steel. The circular bars in the assembly are solid. The bars are solid with a diameter of 15 mm. Assume a fixed rigid support at C and A. A C В 6 kN 3 m 2 m A) Show the FBD and compatibility equation for this problem. B) Determine the support reactions at A and C. (Horizontal forces only) Left side: Fc = Right side: FA =
The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are angle sections with the thickness shown in the figure. The working stresses are 70MPa for shear in the rivets and 140MPa for bearing stress due to the rivets. How many 22mm diameter rivets are required to fasten the following members to the gusset plate: (a) BC; and (b) BE? 000 4 m B с 96 kN D 6 m E 200 KN 4 m F G 4 m 96 kN H to- PBC - -14-mm-thick gusset plate -13-mm-thick angle 6-mm-thick angle PBE