! Required information The hydraulic cylinder CF, which partially controls the position of rod DE, has been locked in the position shown. Member BD is 15 mm thick and is connected at C to the vertical rod by a 9-mm-diameter bolt. Know that P= 2.9 kN and e = 75°. 100 mm- 175 mn 20° E 200 mm F 45 mm Determine the bearing stress at Cin member BD. The bearing stress at Cin member BD is 50.7| MPa.

! Required information The hydraulic cylinder CF, which partially controls the position of rod DE, has been locked in the position shown. Member BD is 15 mm thick and is connected at C to the vertical rod by a 9-mm-diameter bolt. Know that P= 2.9 kN and e = 75°. 100 mm- 175 mn 20° E 200 mm F 45 mm Determine the bearing stress at Cin member BD. The bearing stress at Cin member BD is 50.7| MPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

a) Find minimum diameter needed if the allowable shear stress is I40 Mpa and the rotation of point A can't exceed 2.5 degrees. →Shaft made of steel 10 kN-m 4KN m 2KN -m 450 g00 mm 1goo mm A mm
The hydraulic cylinder CF, which partially controls the position of rod DE, has been locked in the position shown. Member BD is 5/8 in. thick and is connected to the vertical rod by a 3/8-in.-diameter bolt. Determine (a) the average shearing stress in the bolt, (b) the bearing stress at C in member BD.
2. The crank mechanism shown below is in equilibrium. Determine: a) the diameter of cylindrical connecting rod CD, given that normal stress is limited to 120MPa; b) the shear stress in the pin at B, where the pin has diameter of 8mm; and c) the bearing stress in the bracket supports at B. C 120° A 8kN 300mm B 30⁰ D P 200mm 6mm B 15mm 6mm 8mm Detail of pin and pin brackets
A pressure vessel of 10-in. inner diameter and 0.25-in. wall thickness is fabricated from a 4-ft section of spirally welded pipe AB and is equipped with two rigid end plates. The gage pressure inside the ves-sel is 300 psi, and 10-kip centric axial forces P and P′ are applied to the end plates. Determine (a) the normal stress perpendicular to the weld, (b) the shearing stress parallel to the weld.
dAB The bracket BCD as shown in the figure is subjected to two forces, 50 KN and 10KN. a. If the control rod AB is made of a steel having an ultimate normal stress of 600MPA, determine the diameter of the 50KN 10KN rod for which the factor of safety with respect to failure will 0.6 m be 3.3. b. Suppose that the pin at C is to be made of a steel with an ultimate shearing stress of 350MPA. Determine the diameter of the pin C for which the factor of safety with respect to shear will also be 3.3. |-03 m- -0.3 m c. Determine the required thickness of the bracket supports at C knowing that the allowable bearing stress of the steel used is 300MPA. Ultimate Strength Factor of Safety Allowable Strength
*R9 4. Two A36 steel pipes, cach having a cross-sectional area of 200 mm, are screwed together using a union at B as shown. Originally the assembly is adjusted so that no load is an the pipe. If the union is then tightened so that its screw, having a lead of 0.55 mm, undergoes two full turns, determine the average normal stress developed in the pipe. Assume that the union at B and couplings at A and C are rigid. Neglect the size of the union. Note: The lead would cause the pipe, when unloaded, to shorten 055 mm when the union is rotated ane revolution. -09m- a6 m.
The staves or vertical members of the wooden tank are held together using hoops having a thickness of 19 mm and a width of 54 mm. The spacing of hoops is 291 mm. The wooden tank has a radius of 479 mm. Determine the stress in hoops (kPa) if the tank is subjected to an internal gauge pressure of 17 kPa and this loading is transmitted directly to the hoops. s/2 s/2 AC B-
13-11. The staves or vertical members of the wooden tank are held together using semicircular hoops having a thickness of 12 mm and a width of S0 mm. Determine the normal stress in hoop AB if the tank is subjected to an internal gauge pressure of 14 kPa and this loading is transmitted directly to the hoops. Also, if 6-mm-diameter bolts are used to connect cach hoop together, determine the tensile stress in each bolt at A and B. Assume hoop AB supports the pressure loading within a 300-mm length of the tank as shown. 450 mm зфтm 150 mm 150 mm з mm
Calculate the shear stress in MPa at section B A 100 mm F-10EN 10 mm
Q3: . A crank built up from cylindrical sections by welding required a loading of 250 lb to overcome the resistance when in the post- tion shown. (a) Compute the maximum normal and shear stresses induced in the section A-A. (b) Determine the maximum shear stresses induced in parts I, II, and III. Ans. (a) (max) = 29,000 psi, T(max) = 15,000 psi (b) 10,550 psi for part I, 6880 psi for II, 15,000 psi for III --A III II 1 Dia. Dia. Fig. 2-38 250 lb 150 "Dia.
Q3- Detemine minimum yield stress requiredfor fabricating the pipe shown in figure (Q3). The pipe is subjected to a vertical load of (50N down) and a momentof(70 N.m) at its endA.Use Tresca theory and a factor of safety (2) to solve at point C. www w 0.75 m 0.5 m D В 50 N 1.25 m 70 N-m Figure (Q3)
4G ll. 91 jo 78 Home work The copper pipe has an outer diameter of 40mm and an inner diameter of 37mm. If it is tightly secured to the wall at A and three torques are applied to it as shown below in the figure. Determine the absolute maximum shear stress developed in the pipe 2ON.m 8ON M 3ON.M هوم و ورك مقاومه التسليم الثلاثاء القادم. . . ناطق العیدان 29/12/21