The structure supports a distributed load of "w". The limiting stress in rod (1) is 380 MPa, and the limiting stress in each pin is 200 MPa. If the minimum factor of safety for the structure is 2.10, determine the maximum distributed load magnitude w that may be applied to the structure plus the stresses in the rod and pins at the maximum w.

The structure supports a distributed load of "w". The limiting stress in rod (1) is 380 MPa, and the limiting stress in each pin is 200 MPa. If the minimum factor of safety for the structure is 2.10, determine the maximum distributed load magnitude w that may be applied to the structure plus the stresses in the rod and pins at the maximum w.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The d = 16-mm-diameter solid rod passes through a D = 21-mm-diameter hole in the support plate. When a load P is applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 11 mm. The rod head has a diameter of a = 32 mm, and the head has a thickness of t = 10 mm. The shear stress in the rod head cannot exceed 130 MPa, the punching shear stress in the support plate cannot exceed 90 MPa, and the bearing stress between the rod head and the support plate cannot exceed 145 MPa. Determine the maximum value of Pmax that can be supported by the structure. P Support Plate Rod Answer: Pmax i Hole diameter D Head KN
The ends of the compound shaft are attached to rigid walls. The maximum shear stress is limited to 60 MPa for the bronze segment AB and 84 MPa psi for the steel segment BC. Determine the diameter of each segment so that each material is simultaneously stressed to its permissible limit when the torque T = 40 kN-m is applied as shown. The shear moduli are 35 GPa for bronze and 80 GPa for steel. Bronze Steel B A T 3 m 2 m
All forces applied in the system are in the (x - y) plane. The material point B at the top of the beam is rotated at an angle of 15° counterclockwise. It is required that the shear stress is 17.5 MPa for this rotated material point B. At the bottom point A of the beam it is required that the maximum tensile stress is 110 MPa. Determine the load P and the length d that satisfies these constraints defined for points A and B. Given data: L= 4 b, t = b / 25, c = 2b, b = 1000 mm, e = 12, f=5 b/4- q = 2P/L b/ 4 -b/4- P
Question # 4: Determine the state of stress at point A on the cross section at section a-a of the cantilever beam. Show the results in a differential element at the point. ( 2 m a 0.5m 400 KN 100 mm 300 mm 100 mm Section a-a
3. For the given state of stress, determine the principal planes, the principal stresses, the max shear stress. You must use Mohr's Circle. 20 MPa 32 MPa 55 MPa
A beam shown in Figure 7.7 is made of T beam, determine maximum shearing stress develop due to various type of loading. w- 3kN/m A B 2.0m 2.0m 2.0m
Problem 2. [Concepts: Internal forces in 2D and average normal stress] The bars of the truss each have a cross-sectional area of 1.25 in². a) Determine the average normal stress in each member due to the loading P = 8 kip. State whether the stress is tensile or compressive. b) If the maximum average normal stress in any bar is not to exceed 20 ksi, determine the maximum magnitude P of the loads that can be applied to the truss. 4 ft 4 ft 4 E 0.75 P 0
At a point on the free surface of a stressed body, a normal stress magnitude of Sy = 63 MPa (C) and an unknown positive shear stress exist on a horizontal plane. One principal stress at the point is 9 MPa (C). The absolute maximum shear stress at the point has a magnitude of 81 MPa. Determine the unknown stresses on the horizontal and vertical planes and the unknown principal stress at the point. S, Sxy S Answers: i MPa Txy = i MPа Op2 = i MPa
The copper rod AB and steel rod BC are joined at the collar B and fixed connected at their ends. If there is no load in the members when T1 = 17°C, determine the average normal stress in each member when T2 = 47°C. Also, how far will the collar be displaced? The cross-sectional area of each member is 1130 mm?. %3D Сopper Steel Elastic Modulus (GPa) 120 200 Coefficient of thermal expansion (1/°C) 17x10-6 12x10-6 В 1 m 0.6 m-
(Problems No. 1 - 3) The state plane stress at a point is represented by the stress element below. Determine the stresses acting on an element oriented 30 degree counterclockwise respect to the original element. Calculate the shearing stress at the xy-face 60 MPa 20 MPa 90 MPa O a. -55 MPa O b. 65 MPa 55 MPa O d. -65 MPa
At a particular point in a structural member a direct tensile stress of 60 N/mm² exists on a plane perpendicular to the longitudinal axis of the member while a direct compressive stress of 40 N/mm? occurs on a plane parallel to this axis; in addition shear and complementary shear stresses of 50 N/mm? act on these planes. If Young's modulus E is 200000 N/mm² and Poisson's ratio v is 0.3 calculate the direct and shear strains on these planes and hence, using a graphical method, determine the principal strains at the point, the maximum shear strain and the angle the plane of maximum principal strain makes with the longitudinal axis of the member. Finally, calculate the principal stresses at the point. Ans. E= 3.6x104, ɛ, = -2.9x104, Yy=6.5x10-4 ɛ1 = 4.95x10, 01 = 80.8 N/mm², o1=-60.8 N/mm. Ɛ11 =-4.25x10 Ymax=9.2x10-, 67.5°
A hollow aluminum tube used in a roof structure has an outside diameter d2= 112mm and an inside diameter d1= 80mm. The tube is 2.80m long, and the aluminum has a shear modulus of G= 28GPa.a. If the tube is twisted in pure torsion by torques acting at the ends, what is the angle of twist, in degrees,when the maximum shear stress is 52MPa?b. What diameter d, in mm, is required for a solid shaft, as shown, to resists the same torque with the same maximum stress?c. What is the ratio of the weight of the hollow tube to the weight of the solid shaft?