4-5 The A-36 steel rod is subjected to the loading shown.If the cross-sectional area of the rod is 60 mm², determinethe displacement of B and A. Neglect the size of the cou-plings at B, C, and D.60°3.30 KN2 kNDCBA8 kN60⁰3.30 KN0.75 m1.50 m0.50 m2 kN

Displacement of b, δb =2.31 mmDisplacement of a, δa = 2.64 mmExplanation:

Answered: 4-5 The A-36 steel rod is subjected to…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

9-6. Determine the normal stress and shear stress acting on the inclined plane AB. Solve the problem using the method of equilibrium described in Sec. 9.1. 9-7. Determine the normal stress and shear stress acting on the inclined plane AB. Solve the problem using the stress transformation equations. Show the result on the sectioned element. 45 MPa 45° Probs. 9-6/7 80 MPa
SECTION: 500mm 20 KN I5 KNIM 1000 mm 12 m Ps 800 KN e : 400 mm (ASSUME IS % LOS SES) A. Determine the stress at the bottom in the free end. (MPa) B. Determine the stress at the top in the fixed end. (MPa)
Read the question carefully and give me right solution with clear calculations
A solid 1.00 in. diameter shaft is subjected to a torque of T = 240 lb-ft and an axial load of P = 5000 lb. (a) Determine the principal stresses and the maximum shear stress at point H on the surface of the shaft. (b) Show the stresses of part (a) and their directions on an appropriate sketch. Answer: (a) Op1 = i Op2 = i Tmax in-plane A i H (1) 요. 요.. psi psi T B psi P X (b) Show the stresses of part (a) and their directions on an appropriate sketch.
The assembly consists of three disks A, B and C that are used to support the load of 140 kN. Determine the smallest diameter d, of the top disk, the diameter d₂ within the support space, and the diameter d of the hole in the bottom disk. The allowable bearing stress for the material is (allow)b = 350 MPa and allowable shear stress is allow=125 MPa. B A 140 KN - dz d₂ 20 mm 10 mm
2. Two 115-mm wide by 15-mm thick steel plates are welded as shown. The load P = 135 kN is concentrically applied and B= 25°. For the xy directions shown, determine a) b) The normal stress or acting perpendicular to the weld; The shear stress try' acting parallel to the weld; Sketch the state of stress to represent results from a) and b) above. В P 2² 115 mm. P
The shown L-shape cantilver is loaded as shown and fixed at A. It has a constant section of 40 mm X 20 mm. For point I located at 50 mm from support A, at the midheight of the section, determine the principal stresses, the principal planes and the maximum shear stress. y 50 mm 150 mm 40 mm 0.5 kN H- I 20 mm 3 kN 160 mm 2.5 kN

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

4-5 The A-36 steel rod is subjected to the loading shown. If the cross-sectional area of the rod is 60 mm², determine the displacement of B and A. Neglect the size of the cou- plings at B, C, and D. 60° 3.30 KN 2 kN D C B A 8 kN 60⁰ 3.30 KN 0.75 m 1.50 m 0.50 m 2 kN