A compound steel [G-82 GPa) shaft consists of solid 34-mm-diameter segments (1) and (3) and tube segment (2), which has an outside diameter of 56 mm and an inside diameter of 51 mm. Determine: (a) the maximum shear stress 7₂ in tube segment (2). (b) the angle of twist ₂ in tube segment (2). (c) the rotation angle Po/A of gear D relative to gear A. 0.3

A compound steel [G-82 GPa) shaft consists of solid 34-mm-diameter segments (1) and (3) and tube segment (2), which has an outside diameter of 56 mm and an inside diameter of 51 mm. Determine: (a) the maximum shear stress 7₂ in tube segment (2). (b) the angle of twist ₂ in tube segment (2). (c) the rotation angle Po/A of gear D relative to gear A. 0.3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Torialai Stan Problem 1-- Short link BD consists of a single steel bar 40 mm wide and 12 mm thick. Knowing that = Call 100 Mpa, determine: a) The maximum value of the normal stress in the link BD b) The required pin diameter at support D. 20kN 100 150 mm 300 mm D 30
0.15
0.16
ABDE rigid rod with single action rivet from point A, point B Connected with BC rod. B and C points of the rod are fence effect rivets. The maximum shear stress that the rivets can bear is 550 MPa, that of the BC bar Since the maximum tensile stress is 440 Mpa, the safety factor FS = 2; 1 ) Calculate the diameter of rivets A and B 2 ) Calculate the diameter of the BC rod
The bell-crank mechanism is in equilibrium for an applied load of F1 = 11 kN applied at A. Assume a = 250mm, b = 100mm, c = 90mm, and θ = 40°. Pin B is in a double-shear connection and has a diameter of 29 mm. The bell crank has a thickness of 31 mm. Determine the shear stress in pin B and bearing stress in the bell crank at B. Express your answer in MPa rounded to the nearest hundredths.
2. Two 115-mm wide by 15-mm thick steel plates are welded as shown. The load P = 135 kN is concentrically applied and B= 25°. For the xy directions shown, determine a) b) The normal stress or acting perpendicular to the weld; The shear stress try' acting parallel to the weld; Sketch the state of stress to represent results from a) and b) above. В P 2² 115 mm. P
All part plzz
13
*4-76 The C83400-red-brass rod AB and 2014-T6-alu- minum rod BC are joined at the collar B and fixed connected at their ends. If there is no load in the members when T₁ = 50°F, determine the average normal stress in each member when T₂ = 120°F. Also, how far will the collar be displaced? The cross-sectional area of each member is 1.75 in². 3 ft B 2 ft C
The bell-crank mechanism is in equilibrium for an applied load of F1 = 19 kN applied at A. Assume a = 280mm, b = 170mm, c = 80mm, and θ = 45°. Pin B is in a double-shear connection and has a diameter of 30 mm. The bell crank has a thickness of 29 mm. Determine the bearing stress in the bell crank at B. Express your answer in MPa rounded to the nearest tenths.
The rod and the tube are of the same initial length and must remain together then the strain in each part must be the same. A compound bar is made up of a rod of an area A1 and modulus of elasticity E1, and a tube of equal length of A2 and modulus of elasticity E2. If a compressive load P is applied to the compound bar, find how the load is shared. The total load carried is P and let if be shared W1 and W2
DProb. 2.8-8. Boom AC in Fig. P2.8-8 is supported by a rec- tangular steel bar BD, and it is attached to a bracket at C by