The oil tanks in Tinyland are only 160 cm high, and they discharge to the Tinyland oil truck through a smooth tube 4 mm in diameter and 55 cm long. The tube exit is open to the atmosphere and 145 cm below the tank surface. The fluid is medium fuel oil with p= 850 kg/m3 and u= 0.11 kg/m-s. Estimate the oil flow rate in cm3/h. For the given flow, take the energy correction factor a = 2.0 for laminar pipe flow. The flow rate is 4623.8 cm3/h.

The oil tanks in Tinyland are only 160 cm high, and they discharge to the Tinyland oil truck through a smooth tube 4 mm in diameter and 55 cm long. The tube exit is open to the atmosphere and 145 cm below the tank surface. The fluid is medium fuel oil with p= 850 kg/m3 and u= 0.11 kg/m-s. Estimate the oil flow rate in cm3/h. For the given flow, take the energy correction factor a = 2.0 for laminar pipe flow. The flow rate is 4623.8 cm3/h.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The velocity of water is measured using an orifice meter (throat diameter = 0.06m) in a 0.31-m pipeline. The measured pressure drop across the orifice is 75 kPa. The Reynolds no. at the orifice is ?
Show that the kinetic energy of oil flowing through a pipe is 1.2961 ft-lbf/s given the folowwing: diameter of pipe = 2 in Flow rate = 40 gal/min SG = 0.90 water density = 62.3 lb/ft3
A 60L/s of heavy oil, p-980kg/m² and v-400mm³/s, is flowing in a 305-mm-diameter pipe. The starting elevation of pipe is z1=85m, the end elevation of pipe z,=105m, and the length of pipe l=1800m. Determine the pressure drop and power loss in the pipe.
Q.8 Venturimeter is installed in a pipe of diameter 40 mm. If the throat diameter of venturimeter is 20 mm and the pressure difference between the pipe and throat section is found to be 120 kPa. Then neglecting the frictional losses, the water velocity in main pipe is (m/s) A В 3 C 4 D 8
What’s the answer for this please ?
It says my answer is partially correct. 264kPa is correct but it says 11.3m is not correct. What is the correct way to calculate this value?
PRELIMS DISCUSSION IN ME 3214 FLUID MACHINERY PROBLEM: A 90-cm ID pipeline (f = 0.020) of length 3000 m connects a reservoir whose water surface elevation is 540 m to a nozzle at elevation of 300m. The jet from the nozzle is used to drive an impulse turbine. If the head loss through the nozzle is expressible as 0.04 E 2g (a) Determine the jet diameter that will give a jet of maximum power. (b) Evaluate this maximum Jet power. Dropared by: ENGR REVNA LDO R MAGAY
Calculate the pressure differential and head loss in a 70-cm-diameter pipe using a 40-cm-diameter orifice meter if the water has a volumetric flow rate of 380 L/s, a density of 998 kg/m, and a dynamic viscosity of 1.002 x 10-3 kg/m-s.
the fluid in a pitot tube is mercury (sg = 13.6) having deflection of 30 cm. calculate the rate of flow in L/s in the 100mm tube if the flowing fluid is oil (sg=0.82). neglect the headloss in the pipe. Answer: 75.2
Water flows through a Venturi meter that is connected to a pipe and a manometer as shown in Figure 3. The diameter of the Venturi meter across point (1) is 4 cm and the pipe outlet diameter across point (2) is 8 cm. A Pitot tube is inserted into the free jet near the outlet at point (3). Assume viscous effect is negligible. Determine: (a) The pressure at point (1). (b) The volumetric flowrate, Q. (c) The height, h, measured by the Pitot tube. 4 cm 8 cm h (3) 12 cm -Mercury (SG = 13.6) Figure 3: Venturi meter connected to pipe and manometer
Prelim discussion fluid
An orifice of 8 cm diameter is fitted in a 20 cm diameter pipe that carries oil of specific gravity 0.8. The mercury manometer attached to the orifice shows a reading of 0.75 m. Calculate the oil flow rate throught the pipe. Assume coefficient of discharge for orifice as 0.6.