PRELIMS DISCUSSION IN ME 3214FLUID MACHINERYPROBLEM:A 90-cm ID pipeline (f = 0.020) of length 3000 m connects a reservoir whose watersurface elevation is 540 m to a nozzle at elevation of 300m. The jet from the nozzleis used to drive an impulse turbine. If the head loss through the nozzle is expressibleas 0.04 E2g(a) Determine the jet diameter that will give a jet of maximum power.(b) Evaluate this maximum Jet power.Dropared by: ENGRREVNA LDO RMAGAY

Answered: Image /qna-images/answer/d46bc73b-8bf0-4069-a4ff-28c0ac5c5667.jpg

Answered: (a) Determine the jet diameter that…

Engineering

Mechanical Engineering

(a) Determine the jet diameter that will give a jet of maximum po (b) Evaluate this maximum Jet power.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: eries of vanes moving with a ii) work done (iii) Efficiency. velocity of 8 m/s. Determine (i) Force…

Q: Q/A uniform flow with a velocity of 4 m/s is flowing over a source placed at the origin. The…

A: Given: Uniform velocity (U)=4m/sStagnation points= (-0.35,0)

Q: single hydraulic turbine is to be selected for a power site with a net head of 30 m. 10 700

Q: Q1. Apply Bernoulli Equation to figures (1) and (2) . Figure (1) pump station Figure (2) free jet

Q: A frictionless convergent-divergent channel is used to accelerate the airflow emanating from the…

Q: Please, explain the physical meaning of the term volume flow rate – determination and

A: For solution refer below images.

Q: True/False: For saturated water with a quality 0 < x < 1, volumetric flow rate can be used to…

A: The process given in the question is accompanied to change of water from saturated water to…

Q: onsider two rectangular tanks having constant flow areas of A1 and A2. The tanks are connected at…

A: Given dataArea of tank 1 = A1Area of tank 2 = A2pipe diameter = dInitial elevation = ho

Q: The turbine shown in figure 2 develops 3000 kW when the water flowrate is 24 Is. The head loss…

Q: A B P4. Two holes are made in the side of the tank such that the jets of water flowing out of them…

A: The text says that the equation below describes the relationship between creep, strain, and time for…

Q: Q3) A gas enters horizontal pipe with a 31O m/s. If the absolute pressure changes from 50 kpa to 80…

A: Given:Inlet velocity, V1=310 m/sinlet Pressure, P1=50 kPaoutlet Pressure, P2=80 kPaTemperature,…

Q: are the primary differences be- ass in terms of pressure rise anc den't 9onu from o hes

A: given:

Q: jet of alcohol strikes the vertical plates shown in the Figure 2. A force F=425 N is required to…

A: ForceF=425ND1=5cmD2=2cmP2=101kPaAlcohol SG=0.79 To-Determine:- 1) The mass flow rate of alcohol.2)…

Q: A jet of water 15 cm in diameter flowing at 360 L/s strikes normal to a fixed plate. (a) What is the…

A: Introduction: The surface's force on the jet is calculated using Newton's Second Law, which states…

Q: 5. Dry saturated steam at 1.25MPA flows along steam main of 150 mm internal diameter at 24m/s.…

A: Given Data V1=24 m/s P1=1.25 MPa, dry saturated D1=150 mm P2=0.12 MPa Ms=4.5 kg Mw=90 kg

Q: 1. Water is draining from an outlet located h below the free surface. What is the minimum h that…

A: Using Bernoulli equation at section 2 and 3 velocity of jet at section 2 can be determined Use…

Q: cross section S with velicity q1 and making an a

A: Liquid jet has cross-section area= S Velocity =q1 Angle =α

Q: Consider the large open tank of water. At a height, h = 1 m, above the bottom, it is connected to a…

Q: water 7.5 cm vapor diameter 1. Water is siphoned from the large, open tank as shown. The 9.2 m gas…

A: Solution: Water vapour on top of the barometer balances the liquid column and thus prevents the…

Q: Problem 4- A 400cm long pipe with a smaller diameter of 3.937 inchesand a larger diameter of 11.81…

A: To Find : The pressure difference in between the smaller and bigger diameter. Given : The length…

Q: 3. Oil with density of 930 kg/m³ enters a diverging nozzle at 6.7 kg/s. If the ratio from the outlet…

A: According to the given data m˙=6.7 kg/s ρ=930kg/m3 A2A1=6 D1=10cm=0.1m We need to find The exit…

Q: A 4.5 m diameter diesel tank has an outlet nozzle of 75 mm in diameter. What is the mass flow rate…

Q: Inside a wind tunnel, the air at the entrance has a pressure of 2100 lbs/ft^2, and a temperature 510…

A: Given Data T1=510 R V1=360 ft/s T2=475 R

Q: Consider the two flows through identical nozzles sketched below. If the reservoir pressures and…

A: Applying continuity equation on 1 and 2 m1= (ρAV)t1=(ρAV)e1 VtVe=AeAt = 4 Vt=4 Ve ...1…

Q: Water enters a fountain through a pipe with a cross-sectional area ?1 at a flowrate ?. The pressure…

Q: Air flows at a rate of 0.85 m3 /s through a horizontal round duet, which is reduced in diameter from…

A: Given:- Air is flowing through a horizontal round duct. volume flow rate of air θ=0.85 m3/s…

Q: A double-overhung impulse-turbine installation is to develop 15,000 bkW at 257 rpm under a net head…

A: P=15000 KwN=257 rpmH= 340 mv=2gHv=2×9.81×340v=81.674 msec

Q: A horizontal water jet from a nozzle of constant exit cross section impinges normally on a…

A: Necessary force increase by factor of 25

Q: 1. A 2-D incompressible steady and potential ow of air a streamfunction of the form is given as Ψ= 2…

A: Given Data Free steam pressure is : P=100 kPa Density of air is : ρ=1.2 kg/m3 Steam function is :…

Q: Figure shows that water leaving a container. What is the exit velocity of the water?

Q: Write the head form of Bernoulli equation

A: ExplanationAccording to Bernoulli total head of a flowing fluid always constant.

Q: 3. Find vi assuming incompressible flow and The tank is very large.

A: To determine the velocity V1.

Q: A water jet of diameter 20 mm is striking on a flat plate with a flow rate of 5 L/s. Determine the…

A: Given Diameter, d = 20 mm = 0.02 m Flow rate, Q =5 L/s = 0.005 m3/s

Q: Control volume concept can be used to obtain forces in both internal and external flow. By drawing a…

A: Control volume concept of force calculation is a simple approach as it directly takes the…

Q: . Indiana Jones needs to ascend a high-rise building. There is a large hose filled with pressurized…

Q: Problem 6.28 - A pilot tube gets to be inserted in a pipe having diameter of 300 mm. The static…

Q: setup a Bernoulli's equation in head form that can be used to determine the pump power requirement.…

Question

PRELIMS DISCUSSION IN ME 3214
FLUID MACHINERY
PROBLEM:
A 90-cm ID pipeline (f = 0.020) of length 3000 m connects a reservoir whose water
surface elevation is 540 m to a nozzle at elevation of 300m. The jet from the nozzle
is used to drive an impulse turbine. If the head loss through the nozzle is expressible
as 0.04 E
2g
(a) Determine the jet diameter that will give a jet of maximum power.
(b) Evaluate this maximum Jet power.
Dropared by: ENGR
REVNA LDO R
MAGAY

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

explained please
A sample of steam is at a pressure of 300 kPa (x=0.75). Solve for its entropy.
Water enters at section 1 at 10 m/s with sp gr of 0.998 and alcohol enters sections 2 at 6 m/s with sp gr of 0.8. Pipes 1, 2 are of 3 cm in diameter and pipe 3 is of diameter 4 cm. Compute the exit velocity and density of the mixture. Assume ideal mixing of incompressible fluids. Please provide complete solution
I need the answer as soon as possible
A flow of water at 1 atm with a vapor pressure of 0.2 psi and a critical cavitation number of 0.3 (Ca critical = Patm-Pvap / 0.5pV2). At what rate does cavitation occur?
solve both parts(hand written)
can someone help me? Thank you.
5
Q#2 Air is flowing through a venture-meter whose diameter is 2.6 in at the entrance part (location 1) and 1.8 in at the throat (location 2). The gage pressure is measured to be 12.2 psia at the entrance and 11.8 psia at the throat. Neglecting frictional effects, show that the volume flow rate can be expressed as 2(P - P2) v = Ar p(1 – AIA}) and determine the flow rate of air. Take the air density to be 0.075 lbm/ft3. 12.2 psia 11.8 psia Air 2.6 in 1.8 in
M1
Find the maximum power developed by the turbine. Data H1= 37 m, H4= 2 1 m, D2=56 cm, D4= 35 cm, V4= 8.5 m/s, P4= 200 kPa, Patm= 100 kPa, 1000 kg/m3. * Lake H, P.O V. h D2 H. Turbine Your answer