Estimate the diameter of the chimney as per the data given below: Mass of flue gases flowing through the chimney=42 kg/s, Density of flue gases =0.56 kg/m³ Velocity of flue gases=20.5 m/s and neglect the losses.

Estimate the diameter of the chimney as per the data given below: Mass of flue gases flowing through the chimney=42 kg/s, Density of flue gases =0.56 kg/m³ Velocity of flue gases=20.5 m/s and neglect the losses.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The machine in the following figure acts as a turbine during daytime to produce electricity and as a…

Q: Water is flowing steadily through a closed pipe system of constant diameter. Station 2 is 1 m higher…

A: Given data: The height of station 2 is, z2 = 1 m. The velocity at station 1 is, v1 = 3 m/s. The…

Q: A frictionless convergent-divergent channel is used to accelerate the airflow emanating from the…

Q: A horizontal pipe of diameter 350 mm converges to a diameter of 200 mm. The pipe conveys water with…

A: Given:The inlet diameter, theoutlet diameter of the tube the inlet pressure, theoutlet pressure The…

Q: 1. GUANZHO Bus Manufacturer install a ventilating fan in each bus with a suction duct diameter 0.315…

A: ● First determine the density of the air at the atmospheric pressure and the given air temperature.…

Q: The turbine shown in figure 2 develops 3000 kW when the water flowrate is 24 Is. The head loss…

Q: Water flows into a house by means of a pipe with an inner diameter of 2,4cm, absolute pressure is…

Q: Air at 10 ° C temperature and 80 kPa pressure enters the emitter of a jet engine at a speed of 200 m…

Q: A simple carburetor under a certain condition delivers 5.45 kg/h of petrol with an air fuel ratio of…

A: Given Data The mass flow rate of the fuel is: m˙=5.45 kg/hr=1.5138×10-3 kg/s The air fuel ratio is:…

Q: A pitot tube is inserted in a 76 cm ID duct carrying air at 42.54C. A pitot tube reading is taken at…

A: Given that, T=35.46 °C,Cd=0.98h1=4 cm,h2=71 cm,Barometric Pressure=760 mm Hgρwater=1000 kg/m3

Q: A liquid a constant density 900 (kg/m3) is flowing at an unknow velocity V1 (m/det) through a…

A: Given: Diameter at section Ais dA=10cm = 0.1m, Diameter of section B is dB=5cm =0,05m, Density of…

Q: Question 3) As seen in the figure, the vacuum pump provides air flow in an insulated pipe with a…

A: Given data, Calculating Mach Number at section using the given relationship: - Hence, the Mach…

Q: You were asked to design a water storage tank for your processing plant. The tank is…

Q: 200 r.p.m. with the wing An impeller rotating at dimensions (b₁ = 1.5 in., b₂ = 1.0 in., D, 5 in.,…

Q: (b) Two reservoirs are connected by a pipeline consisting of pipe 1, pipe 2, pipe 3 connected in…

A: Given: Length of the pipe 1→L1=170 m Length of the pipe 2→L2=300 m Length of the pipe 3→L3=210 m…

Q: Air is discharged from a large tank through a convergent nozzle of 25 mm diameter. The air in the…

A: (a) To find: The mass flow rate of air. Given: The inside pressure is P1=150 kPa. The outside…

Q: A pitot tube is inserted in a 76 cm ID duct carrying air at 42.54C . A pitot tube reading is taken…

Q: 1) Water at temperature T=350 K and pressure 0.25 MPa flows upwards through a vertical pipe with…

A: Given:Water temperature, T=350 KWater pressure, P1=0.25 MPaPipe diameter, d=380 mm=0.380 mPipe…

Q: A pipeline with diameter of 0.2 m. If the inlet pressure = 2400 kPa, outlet pressure = 2300 kPa,…

A: The length of the pipeline.Given:The diameter of the pipeline is .The inlet pressure is .The outlet…

Q: A wind tunnel has an incompressible flow of air, flowing horizontally from an inlet section, 7 times…

A: Given data Inlet Area= A1Test section Area = A2Test Section area = 17 Inlet areaA1A2 = 7Specific…

Q: The inlet pressure to a piping system is 440 kPa. The inlet pipe diameter is 0.6 m. What is the…

Q: A pipeline, 50 cm diameter and 4,500 m long, connects two reservoirs whom constant difference of…

Q: A vertical pipe in the form of a cone has a diameter of 45 cm at the top and 92 cm at the bottom and…

Q: When the pump (figure) delivers 220m^3/h of water at 20°C from the reservoir, the total frictional…

Q: What is the resulting flow rate in the system if three pumps are used in parallel? (a) 0.483 m^3/s…

A: It is given in the question that the pumps are connected in parallel. And we know that when one or…

Q: The calculation of power from moving fluid has the following parameters: Volume flow rate = 10 +/-…

Q: In a 3.5 MW hydroelectric power plant, the elevation of the headwater is 2100 m and that of a…

Q: A fluid enters a pipe at speed v1=0.1 m/s. the diameter of the tube is d=200mm and the fluid flowing…

Q: r=20mm, the friction factor , the shear stress at pipe wall and the head loss per meter of the pipe…

A: Given: s=0.85 ρ=850 kg/m3ν=1.8×10-5 m2/sD=100 mmQ=0.50 L/sTo determine:Center line velocityvelocity…

Q: Air flows steadily from a tank pressurized to 3kPa through a pipe of diameter D = 0.03 m and finally…

Q: Show that the kinetic energy of oil flowing through a pipe is 1.2961 ft-lbf/s given the folowwing:…

Q: fan ventilates at 500rev/min, the airflow is measyured at 150cubic meters/second. the ventilation…

A: fan ventilates = 500 rev/minThe airflow Q2 = 150 m³/secVentilation pressure = 0.40 kPaPressure along…

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Question

Estimate the diameter of the chimney as per the data given below:
Mass of flue gases flowing through the chimney=42 kg/s,
Density of flue gases =0.56 kg/m³
Velocity of flue gases=20.5 m/s and neglect the losses.
The diameter of the chimney in m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Three pipes A,B and C connected in seies discharges 160 L/s of water. The properties of pipe: for pipe A,L= 1800 m, diameter= 0.90 m f= 0.012; for pipe B, L= 1500 m, diameter= 0.60 m f=0.012 and for pipe C, L= 800 m , diameter = 0/45 m, f= 0.012. Disregarding minor losses, find the total head loss of the pipe. Include the diagram in your solution. a.0.078 m. b.1.15 m. c.0.492 m. d.1.675 m.
i need the answer quickly
10.The nozzle shown in the figure creates a horizontal jet of alcohol ( s = 0.79 ) which strikes a vertical plate. If the jet causes a force of ( 500 N ) on the plate, calculate : a) The mass flow rate of alcohol. b) The pressure at section ( 1) if there is no losses in the nozzle. F D=5 cm D;=2 cm Univer Mechar Univers of pert
Water flows through a pipe of 0.0025 m^2size with a uniform velocity of 7m/s and flows out from an ariface at bottom at a rate 0.003 m^3/s. what is rate of change of mass of water in the tank?
A pipe with diameter 30 cm carries oil of sp.gr. 0.95 at a velocity of 4 m/s .at another section the diameter change to 20 cm. Find the velocity at this section and also find the mass flow . rate of oil A- V=8.5m/s , m= 270 kg/s B- v=9m/s, m= 300 kg/s O C- v=9 m/s , m=269.8 kg/s D- v= 9.5 m/s, m= 280 kg/s O
A fluid with a density of 0.8 g/cm3 is being emptied from a very large tank through a small cylindrical opening with a diameter d. Use the figure below to calculate a) the diameter d_of the opening if the mass flow rate at point 2 is 1.45 kg/s, and b) the flow velocity at point 3. 1. H = 4 m d = ? 3 h = 1 m 2.
The pressure drop across a turbine is 200kPa. The flow rate is 0.25m3/min. WHat is most nearly the power output of the turbine?
Kindly solve this problem with complete solution so that I can Understand. Correct Final answer: 40.77
Ex ....... HYDRAUE • The pump is to be connected to a rising main which has a diameter (D) of 400 mm and a length of 137 m.The entry exit and minor head losses in the pipeline can be taken as 80D in this particular situation. The friction loss can be approximated by h; = ALQ² / 1 2D5 with A=0.04. The static lift is 10 m. By considering a single pump (P). And two of the pumps in series (P+P) and parallel (P//P) determine: > the H-Q curve of the two pump combinations » Which combination will be capable of discharging at least 0.3 m³/s, with the ability to pump up to 0.35 m³/s if the need arises. %3D
The properties of the air in the inlet section with A1 = 0.2562 m2 in a converging-diverging channel are given as U1 = 256,2 m/s, T1 = 362 K, P1 = 136,2 kPa (absolute). Find the required cross-sectional area, pressure, temperature, velocity and mass flow rate to obtain sonic (Ma2=1.0) flow at the outlet. Calculate critical values of A*, U*, T*, P*. Solve the problem by making the necessary assumptions and drawing the schematic figure.
Please solve asap.
4. Determine the tension in each cable segment and the distance yD.. YD 7 m B 2 m 2 kN 4 m 5 m 3 m 4 kN