A fluid with a density of 0.8 g/cm3 is being emptied from a very large tank through a small cylindrical opening with a diameter d. Use the figure below to calculate a) the diameter d of the opening if the mass flow rate at point 2 is 1.45 kg/s, and b) the flow velocity at point 3. 1. H = 4 m d = ? 3 h 1 m

A fluid with a density of 0.8 g/cm3 is being emptied from a very large tank through a small cylindrical opening with a diameter d. Use the figure below to calculate a) the diameter d of the opening if the mass flow rate at point 2 is 1.45 kg/s, and b) the flow velocity at point 3. 1. H = 4 m d = ? 3 h 1 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A U-shaped tube is filled with water of density 1000 kg/m3 until the level of the liquid is 28 cm above the bottom of the tube. Then oil of specific gravity 0.78 is poured into one branch of the tube until the level of the liquid in the other branch is 34 cm above the bottom of the tube. (g=9.8m/s2) I) Find the level of the oil-water interface in the branch where the oil was spilled II) Find the level of the oil-air interface in the branch where the oil was spilled
fluid2.pdf -> Example 2 • Water is flowing from hole 1cm radius at the bottom of a closed cylindrical container of 2m diameter. If the height of the water in the container is 2 m and the pressure over the surface of water is 3 atm. calculate how much time it took until the container became empty? P.
Use a paper with properhandwritting. Thank you.
An incompressible fluid is flowing through a pipe that is gradually tampering in size by 0.01 m2/m. What is the change in velocity per meter where the pipe is 0.4 m2 in the cross section and the velocity is 30 m/s.
constant velocity of 3 m/s?[ Note: Neglect the pressure force effects] DA 7.6 cm jet of water strikes a vertical plate in its centroid. Find the velocity of water through the jet if a horizontal force of 44.5 N is applied to: 1) hold the platte stationary. 2) move the plate to the right by a nir
Q(in) is a constant inflow which maintains the water level in the tank. Find the horizontal force needed to hold the tank stationary. If you could make any notes on steps in the method to make it clearer that would be great too. Thanks in advance!
Solve it on priority
The velocity distribution in a 0.02 m diameter horizontal pipe conveying carbon tetrachloride (specific gravity = 1.59, absolute viscosity = 9.6 x 10-6 Pa sec) is given by the parabolic equation: v(r)=0.01(0.12- r?), where v(r) is the velocity in (m/s) at a distance r in (m) from the pipe center. What is discharge? O a. 3.13 x-8 m3/s O b. None of the mentioned O c. 1.047 x 108 m3/sec O d. 4.97 x 109 m3/sec
1. A 100-mm diameter plunger (section 1) is being pushed at 60 mm/s into a tank filled with a fluid with a fluid of SG = 0.68. If the fluid is incompressible, how many pounds per second is being forced out at section 2, D2 = 20 mm? Answer: 0.707 lbf/s
i need the answer quickly
what will be the pressure gradient (kpa/m) at L=30 cm through the nozzle? At L=0, the liquid flows inside the nozzle has a specific gravity S=4.4, at L=0, the velocity is 2 m/s while at L=70 cm, the velocity is 6 m/s. Assume steady and inviscid flow. The velocity varies linearly with distance through the nozzle. 70 cm 6 m/s 2 m/s 60 cm Liquid
4) A constriction in a pipe will cause the velocity to rise and the pressure to fall at section 2 in the throat. The pressure difference is a measure of the flow rate through the pipe. The smoothly necked-down system shown in Figure is called a venturi tube. Find an expression for the mass flux in the tube as a function of the pressure change. (1) HGL 4²² (2)