Water flows through a Venturi meter that is connected to a pipe and a manometer as shown inFigure 3. The diameter of the Venturi meter across point (1) is 4 cm and the pipe outlet diameteracross point (2) is 8 cm. A Pitot tube is inserted into the free jet near the outlet at point (3).Assume viscous effect is negligible. Determine:(a)The pressure at point (1).(b) The volumetric flowrate, Q.(c)The height, h, measured by the Pitot tube.4 cm8 cmh(3)12 cm-Mercury (SG = 13.6)Figure 3: Venturi meter connected to pipe and manometer

Answered: Image /qna-images/answer/e8fd3167-657b-49c8-bad2-2631f662d3a8.jpg

Answered: Water flows through a Venturi meter…

Water flows through a Venturi meter that is connected to a pipe and a manometer as shown in Figure 3. The diameter of the Venturi meter across point (1) is 4 cm and the pipe outlet diameter

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A 2-inch copper pipe connection was made from the basement to the second floor in the building. The…

Q: n orifice of 10 cm diameter is fitted in a 25 cm diameter pipe that carries oil of specific gravity…

Q: Two piezometers (manometers) are placed 1.5m apart in a horizontal plastic pipe as shown in figure.…

Q: 26 Ps Water Water Oil Manometric fluid Manometric fluid Find the pressure difference at two points A…

Q: Question 5: The velocity of a fluid flowing in a pipe is to be measured by two different Pitot-type…

A: From these two arrangements for water as a fluid 2nd arrangement will give more accurate result as…

Q: At point in a pipe that lay flat water in the pipe flows a at spced of S.0 mls and has gauge…

A: by continuity equation Area * Velocity = constantArea at the end of the pipe = 4 Area at the start…

Q: Q2: Determine the discharge through pipe shown in figure below and the gauge reading. Neglect all…

A: Given Data, Specific wt. of air:γa=12 N/m3 ρa=γag=129.81=1.22 kg/m3 ρω=1000…

Q: A 30 cm x 15 cm venturimeter is inserted in a vertical pipe carrying water, flowing in the upward…

A: As per given question A 30 cm x 15 cm venturimeter is inserted in a vertical pipe carrying water,…

Q: What kinds of Differential Pressure Flow meters? And discuss them.

A: Flow meters which are based on the differential pressure measure the velocity of fluid by reading…

Q: Pressure loss along a pipe pumping water is 6.6Pa. If the pipe is 2.1m long, what angle (in degrees)…

A: To overcome the pressure drop along the pipe, we need to consider the effect of gravity on the water…

Q: A 30 cm x 15 cm venturimeter is inserted in a vertical pipe carrying water, flowing in the upward…

A: GivenventurimeterD1=30 cm=0.30 mD2=15 cm=0.15 mFluid passing through venturimeter is water…

Q: A mercury manometer installed across an orifice meter (diameter = 1.2 cm) in a horizontal pipe…

A: Given: d = 1.2 cm = 0.012 mD = 2.35 cm = 0.0235 mh = 12 cm = 0.12 m Taking the density of mercury as…

Q: A 30 cm x 15 cm venturimeter is inserted in a vertical pipe carrying water, flowing in the upward…

A: Few points regarding venturimeter. A venturimeter is a device which is used for the measurement of…

Q: : For the multiple pipe system below, calculate (a) the flow in each pipe and (b) Q2, the gauge…

Q: Water flows through a 61-cm by 122-cm conduit at a flow rate of 2000 CMH. The horizontal conduit was…

A: Given:Size of the duct, A=61 cm* 122 cm=0.61 m*1.22 m=0.7442 m2Water flow rate, Q=2000…

Q: A 3.81-cm diameter venturi meter is installed in a pipe with an internal diameter of 10.23 cm. A 127…

Q: A venturi meter has an inlet diameter of 65 mm and a throat diameter of 26 mm. When measuring the…

A: A venturimeter is a device which is used for the measurement of discharge of an incompressible…

Q: An orificemeter with ortfice diameter 12 cm is inserted in a pipe of 20 cm diameter. The pressure…

A: Given Data, d0=12 cm=0.12 m (orifice)d1=20 cm=0.2 m (pipe)p1-p0=9.81 N/cm2Cd=0.6

Q: A 300 mm x 150 mm venturimeter is inserted in a vertical pipe carrying water flowing in upward…

Q: Water is flowing through point 1 (D = 22mm) and point 2 (d = 17mm) in the above venture meter. What…

A: According to the given data D1=222mm D2=17mm Q˙=0.70zl/s We need to find P1-P2

Q: In the Venturi of the kerosene figure (density: = 0.85 ) seeps as ideal fluid. The area in section…

A: Given data: V1=4.5 m/sV2=9 m/sγ=133280 N/m3SG=0.85 Need to determine the value of h.

Q: A venturi meter has an inlet diameter of 65 mm and a throat diameter of 26 mm. When measuring the…

Q: The velocity distribution in a 0.02 m diameter horizontal pipe conveying carbon tetrachloride…

Q: A pipe is horizontal and carries oil that has a viscosity of 0.14 Pa s. The volume flow rate of the…

A: Given Viscosity = 0.14 Pa. s Flow rate, Q = 5.3 × 10-5 m3/s Radius, R =…

Q: The inlet and throat diameters of a horizontal venturimeter are 30 cm and 15 cm respectively. The…

Q: essure the flow ra

A: given:

Q: nm2 is inserted in a pipe of area 175E The pressure difference measured b nercury oil differential…

A: Given Data⇒ Area of orifice meter is A1=878 mm2A1=0.000878 m2 Area of pipe is A2=1756 mm2A2=0.001756…

Q: . Three reservoirs are connected, if pipe (1) and pipe (3) having equal discharge, and the discharge…

Concept explainers

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.

Question

Water flows through a Venturi meter that is connected to a pipe and a manometer as shown in
Figure 3. The diameter of the Venturi meter across point (1) is 4 cm and the pipe outlet diameter
across point (2) is 8 cm. A Pitot tube is inserted into the free jet near the outlet at point (3).
Assume viscous effect is negligible. Determine:
(a)
The pressure at point (1).
(b) The volumetric flowrate, Q.
(c)
The height, h, measured by the Pitot tube.
4 cm
8 cm
h
(3)
12 cm
-Mercury (SG = 13.6)
Figure 3: Venturi meter connected to pipe and manometer

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Explain each step please
What’s the answer for this please ?
Explain the measuring the pressure drop across a flow section or a flow device by a differential manometer.
Problem 4 (a) Water from a water reservoir is delivered through a 2-cm pipe to a 200-litre tank as shown in Figure below. The water level (H) is at 2 m above the pipe. Calculate (a) the time it would take to fill the tank and (b) the height difference of the mercury, h in a U-tube manometer. State all assumptions needed. (Non-anonymous questionO) * h H Water Mercury S.G. =13.6 Jet 200-litre Tank
An orifice of 2.58 cm diameter is placed in a pipe of 5.1 cm diameter. The pipe delivers oil of specific gravity of 0.8. if the pressure difference on the two sides of the orifice is measured by a mercury-oil manometer and the differential gauge reads 125 mm of mercury, calculate the Actual and Ideal rate of flow in liter per second if Cd = 0.63
B4. An orifice meter with orifice area 1072 mm2 is inserted in a pipe of area 2144 mm2 .The pressure difference measured by a mercury oil differential manometer on the two sides of the orifice meter gives a reading of 75 cm of mercury. Find the rate of flow of oil of sp. gr. 0.85 when the co-efficient of discharge of the orifice meter = 0.6. Head of water (in m) The discharge of water through pipe (in Litres/sec)
An orifice meter with orifice area 931 mm² is inserted in a pipe of area 1862 mm2 .The pressure B4. difference measured by a mercury oil differential manometer on the two sides of the orifice meter gives a reading of 75 cm of mercury. Find the rate of flow of oil of sp. gr. 0.75 when the co-efficient of discharge of the orifice meter = 0.6. (Enter only the values by referring the unit given. Also upload the hand written answers in the link provided) Head of water (in m) The discharge of water through pipe (in Litres/sec)
A 200 mm long pipe slopes down at 1 in 100 and tapers from 0.25m diameter to 0.15 diameter at the lower end. If the pipe carries 100 litres of oil of specific gravity 0.85 find the pressure at the lower end. The upper end gauge reads 50 KPa.