The mass of fine aggregate B has been reduced and weighed to conduct an aggregate test shown in Table 2. (e) Calculate the dry bulk specific gravity, SSD bulk specific gravity, apparent specific gravity, and the aggregate absorption. 500.8 gMass of Aggregate500.2 gSSD Mass of Aggregate623 gMass of pycnometer with water938.2 gMass of pycnometer with water and aggregate452 gMass of aggregate at cool temperatureTable 2: Weighed Mass of Aggregate B.

Answered: Image /qna-images/answer/0d65788c-7f67-4fa7-9830-8fbcae0d88be.jpg

The mass of fine aggregate B has been reduced and weighed to conduct an aggregate test shown in Table 2. (e) Calculate the dry bulk specific gravity, SSD bulk specific gravity, apparent specific gravity, and the aggregate absorption.

The mass of fine aggregate B has been reduced and weighed to conduct an aggregate test shown in Table 2. (e) Calculate the dry bulk specific gravity, SSD bulk specific gravity, apparent specific gravity, and the aggregate absorption.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

There are two sources of aggregates (A, B). A sample has been taken from both sources and measured their mass as shown in table below. Measurement Wet mass (9) Oven-dry mass (g) Aggregate A 500 480 Aggregate B 600 564 (a) Determine the total moisture content for the samples from both aggregate sources, respectively. (b) Determine the total moisture content for an aggregate blend with 30% of aggregate A and 70% of aggregate B.
The mass of the aggregates to be tested in Los Angeles Abrasion Machine is 10,000g, what is the % abrasion if the mass of the aggregate retained in No. 12 Sieve is 8435.9g? a 18.5% b 16.0% c 15.2% d 17.3%
7. A sample of fine aggregate weighs 544 g when SSD and 530 g when OD. The flask weighs 654 g when filled with water and 985 g when filled with fine aggregate and water. Calculate the bulk specific gravity, apparent specific gravity, and absorption.
Laboratory specific gravity and absorption tests are run on two coarse aggregate sizes, which have to be blended. The results are as follows: Aggregate A: Buck specific gravity = 2.395; absorption = 4.69% Aggregate B: Buck specific gravity = 2.601; absorption = 0.51% What is the specific gravity of a mixture of 50]% aggregate A and 50% aggregate B by weight?
Design a Mix for the following Data. Specified strength = (99.5) MPa, Required Slump = 80 mmMaximum size of aggregate = 25 mm, FM of fine aggregate = 2.40Grading of aggregate as satisfied by ASTM C33 (American Society for Testing and Materials)SSD specific gravity of fine and coarse aggregate = 2.75Rodded bulk density of coarse aggregate = 1600 kg/cubic mAbsorption Capacity of coarse aggregate = 0.9 %Absorption Capacity of fine aggregate = 0.5 %Moisture Content of fine and coarse aggregate = 2 %Exposure Conditions = Normal
10. A sample of coarse aggregate weighs 1072 g when oven- dried, 1091 g when saturated surface-dried, and 667.6 g when submerged. Calculate the bulk specific gravity, apparent specific gravity, and absorption.
5.10 Samples of coarse aggregate from a stockpile are brought to the laboratory for determination of specific gravities. The following weights are found: Mass of moist aggregate sample as brought to the laboratory: 5,298 g Mass of oven dried aggregate: 5,216 g 5.11 5.12 5.13 5.14 Mass of aggregates submerged in water: 3,295 g Mass of SSD (Saturated Surface Dry) Aggregate: 5,227 g Find a. The aggregate bulk dry specific gravity b. The aggregate apparent specific gravity c. The moisture content of stockpile aggregate (report as a percent) d. Absorption (report as percent) Base course aggregate has a target dry density of 1917 kg/m³ in place. It will be laid down and compacted in a rectangular street repair area of 600 m × 15 m × 0.15 m. The aggregate in the stockpile contains 3.1% moisture. If the required compaction is 95% of the target, how many tons of aggregate will be needed? Calculate the percent voids between aggregate particles that have been com- pacted by rodding, if the…
2. Students in the materials lab performed the specific gravity test (ASTM C127) on coarse aggregate and they obtained the following data: a. Dry weight = 3862.1 g b. SSD weight = 3923.4 g c. Submerged weight = 2452.1 g Calculate the specific gravity values (dry bulk and SSD).
If needed assume the unit weight of water to be 62.4 lb/ft3 a) A HMAC sample has the following volumetric properties (i) VMA = 0.1865 ft3and (ii)Volume of air = 0.0452 ft3 Compute %VFA. b) A HMAC sample has 140 lbs of aggregate with a bulk specific gravity of 2.65 and aneffective specific gravity of 2.71. Based on this information the volume of the absorbedasphalt is ________________ft3A compacted sample of hot mix asphalt concrete sample has a unit weight of 135 lb/ft3.c) The sample has an asphalt content of 5% (by weight). Assume no absorbed asphalt.The bulk specific gravity of the aggregate is 2.65, and specific gravity for the asphaltcement is 1.05. Based on this information compute VMA for this mixture.
Sieve analysis test for fine aggregates was performed on a sample of fine aggregates and produced the following results: a. Calculate the percent passing through each sieve. b. Plot the percent finer in a semi-log gradation chart. c. What is the maximum aggregate size of the sample? d. What is the nominal maximum aggregate size of the sample? e. What is the fineness modulus? Is it in typical range? " Sieve Size, 9.5 4.75 3.35 2.36 2.00 1.18 0.85 0.60 0.425 0.30 0.25 0.18 0.15 (No. 0.075 Pan mm (in) (3/8) (No. 4) (No. 6) (No. 8) (No. 10) (No. 16) (No. 20) (No. 30) (No. 40) (No. 50) (No. 60) (No. 80) 100) (No. 200)| Amount 25 59 75 86 115 136 169 192 225 198 173 112 90 33 12 Datained.
Sieve analysis test for fine aggregates was performed on a sample of fine aggregates and produced the following results: a. Calculate the percent passing through each sieve.b. Plot the percent finer in a semi-log gradation chart.c. What is the maximum aggregate size of the sample?d. What is the nominal maximum aggregate size of the sample?e. What is the fineness modulus? Is it in typical range?