1. In the specific gravity and absorption experiment, the following measurements were taken of coarse aggregates: Weight of pan used to weigh SSD aggregates Weight of pan + SSD aggregates Weight of SSD aggregates in water • Weight of pan used to weigh oven-dried aggregates • Weight of pan + oven dried aggregates Calculate the following properties: a. Specific gravity b. SSD specific gravity c. Apparent specific gravity = 500 g = 2550 g = 1300 g = 510 g = 2545 g

1. In the specific gravity and absorption experiment, the following measurements were taken of coarse aggregates: Weight of pan used to weigh SSD aggregates Weight of pan + SSD aggregates Weight of SSD aggregates in water • Weight of pan used to weigh oven-dried aggregates • Weight of pan + oven dried aggregates Calculate the following properties: a. Specific gravity b. SSD specific gravity c. Apparent specific gravity = 500 g = 2550 g = 1300 g = 510 g = 2545 g

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The following are the results in the test for specific gravity of fine aggregates:Mass of Oven-dried specimen in air = 502gMass of Pycnometer filled with water, to calibration mark = 640gMass of Saturated Surface Dry Specimen = 510gMass of Pycnometer filled with specimen and water to calibration mark = 950gCalculate the absorption, apparent specific gravity, bulk specific gravity in SSD condition, and bulk specific gravity in OD condition
Samples of coarse aggregate from a stockpile are brought to the laboratory for determination of specific gravities and absorption. The following masses were obtained.Mass of moist aggregate = 3,500 gramsMass of oven-dried aggregate = 3,420 gramsMass of aggregates submerged in water = 1,800 gramsMass of SSD aggregate = 3,430 gramsDetermine;a) bulk dry specific gravityb) bulk SSD specific gravityc) apparent specific gravityd) moisture content of stockpile aggregate, in percente) absorption, in percentf) free moisture
Samples of coarse aggregate from a stockpile are brought to the laboratory for determination of specific gravities and absorption. The following masses were obtained.Mass of moist aggregate = 3,500 gramsMass of oven-dried aggregate = 3,420 gramsMass of aggregates submerged in water = 1,800 gramsMass of SSD aggregate = 3,430 gramsDetermine;a) moisture content of stockpile aggregate, in percentb) absorption, in percentc) free moisture new solution please
Specific Gravity and Absorption of Coarse Aggregates What are the possible discussion of observations for specific gravity and absorption of aggregate to observed values?
Coarse and fine aggregates defined as the particles that are retained on a 4.75 mm sieve and pass through a 4.75 mm sieve, respectively. Select one: O True on O False
a. For an aggregate sample, if you know that the apparent relative density is 2.72 and the water absorption is 1.2%. The dry mass of the aggregate is 514 gm. Find the bulk and saturated surface dry (SSD) relative density values? b. Why does the maximum size of aggregate depend on the clear spacing between bars? Show with a simple sketch. Note: Please answer both a and b... Please answer the both questions.. I don't want single b answer.. thank you
Qиestion no.08 The result of specific gravity test is given below Weight of saturated aggregate in water =618gm Weight of oven dry sample = 982 gm Weight of saturated surface dry aggregate = 990 gm (i) Calculate the specific gravity of aggregate?
Sample of coarse aggregate from a stockpile are brought to the laboratory for determination of specific gravities and absorption. The following masses were obtained.Mass of moist aggregate = 5,982 gramsMass of oven-dried aggregate = 5,892 gramsMass of aggregates submerged in water = 4,082 gramsMass of SSD aggregate = 5,897 grams a) absorption, in percentb) moisture content of stockpile aggregate, in percentc) free moisture
H.W. Fine aggregate sample was tested to find its physical properties. The test results were as follows: Bulk specific gravity= 2.45, Apparent specific gravity 2.5, mass of the vessel full of water = 1300 gm, mass of the vessel plus sand and topped up with water= 1500 gm, mass in wet condition 518 gm. Calculate 1- absorption% 2- moisture content% 3- Bulk density 4- Apparent density A-D % Absorption = D D- (B-C) Apparent Specific Gravity = Container SSD Aggregate (A) OD Aggregate (D) Container SSD Bulk Sp.Gr. = with H,O (C) with H,O and with A-(B-C) Aggregate (B) Weight of Agg. (W,) Sp.Gr.= Weight of an equal volume of water (V,*P) PA Density of Agg. Pw Density of Water
Q2 (a) A specific gravity test was performed on a sample of fine aggregate and produced the following results: Mass of sand (saturated surface dry) = 520g Mass of sand (oven dry) = 510g Mass of pycnometer with full of water = 1550g Mass of pycnometer with sand and water = 1900g
Q2 (a) A specific gravity test was performed on a sample of fine aggregate and produced the following results: Mass of sand (saturated surface dry) = 520g Mass of sand (oven dry) = 510g Mass of pycnometer with full of water = 1550g Mass of pycnometer with sand and water = 1900g i. Calculate the apparent specific gravity of the fine aggregate. ii. Calculate the gross apparent specific gravity of fine aggregate.
Sample of coarse aggregate from a stockpile are brought to the laboratory for determination of specific gravities and absorption. The following masses were obtained.Mass of moist aggregate = 5,982 gramsMass of oven-dried aggregate = 5,892 gramsMass of aggregates submerged in water = 4,082 gramsMass of SSD aggregate = 5,897 gramsDetermine;a) apparent specific gravityb) bulk dry specific gravityc) bulk SSD specific gravityd) absorption, in percente) moisture content of stockpile aggregate, in percentf) free moisture