Sieve analysis test for fine aggregateswas performed on a sample of fineaggregates and produced the followingresults:a. Calculate the percent passingthrough each sieve.b. Plot the percent finer in a semi-loggradation chart.c. What is the maximum aggregate sizeof the sample?d. What is the nominal maximumaggregate size of the sample?e. What is the fineness modulus? Is it intypical range? "Sieve Size,9.54.753.352.362.001.180.850.600.4250.300.250.18 0.15 (No.0.075Panmm (in)(3/8) (No. 4) (No. 6) (No. 8) (No. 10) (No. 16) (No. 20) (No. 30) (No. 40) (No. 50) (No. 60) (No. 80)100) (No. 200)|Amount25597586115136169192225198173112903312Datained.

Answered: Sieve analysis test for fine aggregates…

Sieve analysis test for fine aggregates was performed on a sample of fine aggregates and produced the following results:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A 12.80 lb sample of quartzite was found to have the following amounts of material retained on each…

Q: 3.33 The following data are obtained from a tensile test of a 12.7-mm-diameter aluminum specimen…

A: As per the Guidelines of Bartleby We are supposed to answer only first three subparts. Ultimate…

Q: 5. A tensile test was done on a magnesium sample of original diameter and original length of 12mm…

A: To plot the stress v/s strain curve and to find the required parameters Note: as per the answering…

Q: In a particular material, if the modulus o rigidity is equal to the bulk modulus, th Poisson Ratio…

Q: Sieve analysis test for fine aggregates was performed on a sample of fine aggregates and produced…

Q: Q1: A tensile test uses a circular test specimen that has a gage length of 50 mm and diameter = 20…

A: Given that, gage length = 50 mm diameter = 20 mm loat at 0.2% yield point = 100,000 N gage length…

Q: sp wt of SSD CA = 6135 g wt of submerged CA = 3901 g wt of oven-dry CA = 6008 g Calculate the bulk…

A: A=weight of oven dry coarse aggregate B=weight of SSD coarse aggregate C=weight of submerged coarse…

Q: For a fine aggregate, the value of fineness modulus was calculated to be 2.30. Is the particle size…

A: Fineness modulus indicates how coarse or fine an aggregate is. Higher the fineness modulus coarser…

Q: Distinction between clay minerals and nonclay minerals.

A: Clay minerals are hydro-aluminium phyllosilicates, which can also contain alkaline earths, iron,…

Q: Sieve size (mm) 10 5 2.36 1.18 0.6 0.3 0.15 0.075 Wt. retained (g) 0 7 30 33 62 98 55 18 Retained…

Q: A sample of wet aggregate weighed 297.2 N. After drying in an oven, this sample weighed 281.5 N. The…

Q: The fineness modulus is a relative measure of how coarse or how fine an aggregate sample is.…

A: The fineness modulus is a value that signifies the average value of particle size.

Question

Sieve analysis test for fine aggregates
was performed on a sample of fine
aggregates and produced the following
results:
a. Calculate the percent passing
through each sieve.
b. Plot the percent finer in a semi-log
gradation chart.
c. What is the maximum aggregate size
of the sample?
d. What is the nominal maximum
aggregate size of the sample?
e. What is the fineness modulus? Is it in
typical range? "
Sieve Size,
9.5
4.75
3.35
2.36
2.00
1.18
0.85
0.60
0.425
0.30
0.25
0.18 0.15 (No.
0.075
Pan
mm (in)
(3/8) (No. 4) (No. 6) (No. 8) (No. 10) (No. 16) (No. 20) (No. 30) (No. 40) (No. 50) (No. 60) (No. 80)
100) (No. 200)|
Amount
25
59
75
86
115
136
169
192
225
198
173
112
90
33
12
Datained.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A sieve analysis test for fine aggregates was performed on a sample of fine aggregates and produced the following results below. Determine the following: a. Percent passing through each sieve (Tabulation) b. Plot of the percent finer in the Semi-Log Gradation Chart c. Maximum Aggregate Size of the Sample (mm) d. Nominal Maximum Aggregate size of the sample e. Fineness Modulus
1. A bioengineer reports that the Young's modulus of articular cartilage is 0.45 MPa and its Poisson's ratio is 0.46. (i) Determine the aggregate modulus of the cartilage.
For a given elextic material, the Eastic Modulus E is 210 GPa and its Poission's Ratio is 0.27. What is the approximate value of its Modulus of Rigidity? A WRONG B C 105 GPa CORRECT D 83 GPa 159 GPa 165 GPa
On the basis of extensive tests, the yield point of a particular type of mild steel-reinforcing bar is known to be normally distributed with o = 100. The composition of the bar has been slightly modified, but the modification is not believed to have affected either the normality or the value of o. (a) Assuming this to be the case, if a sample of 81 modified bars resulted in a sample average yield point of 8417 lb, compute a 90% CI for the true average yield point of the modified bar. (Round your answers to one decimal place.) Ib (b) How would you modify the interval in part (a) to obtain a confidence level of 92%? (Round your answer to two decimal places.) |---Select-- v should be changed to
Concrete
By using ACI method.
A cylindrical metal specimen having an original diameter of 10.63 mm and gauge length of 50.1 mm is pulled in tension until fracture occurs. The diameter at the point of fracture is 7.60 mm, and the fractured gauge length is 74.5 mm. Calculate the ductility in terms of (a) percent reduction in area (percent RA), and (b) percent elongation (percent EL). (a) i percent RA (b) i percent EL
The wet mass of an aggregate sample is 583g and its dry mass is 575g. The test shows the absorption as 1.5%. what is the moisture condition of this aggregate? O Air dry Bone dry O Moist O SSD
Q4/ A. Explain why ceramic materials do not response to the plastic deformation processes? Also clarify why flexural test is applied to ceramics instead of tensile test? B. Estimate whether a cylindrical aluminum oxide sample will fail or not when it subject to flexural test to achieve flexural strength of 390 MPa knowing that the sample radius is 2.5 mm, separation distance is 30 mm, and the applied load is 620 N respectively.
Brinnell hardness testing can be used for both Ferris and nonferrous metals. The test for ferrous metals requires a 500 kg load for 30 seconds and the test for nonferrous metals requires a 3000 kg load for 15 seconds.
Distinguish porosity from voids content for aggregate with the help of schematic diagrams.
Laboratory specific gravity and absorption tests are run on two coarse aggregate sizes, which have to be blended. The results are as follows: Aggregate A: Buck specific gravity = 2.395; absorption = 4.69% Aggregate B: Buck specific gravity = 2.601; absorption = 0.51% What is the specific gravity of a mixture of 50]% aggregate A and 50% aggregate B by weight?